Primus FF10 Programming Manual Download Page 105

Page: 105 / 136

100962 G PUBLICATION DATE 24 JUN 2008.DOC

PROGRAMMING MANUAL

103

Diagnostic Test Sequence for Machines with Front Soap Hopper.

Test (2) : For washing machines with 2 Main Water Supplies.

Test (3) : For washing machines with 3 Main Water Supplies.

Test

(2)

Test

(3)

Info Explanation

1 1

Black display followed

by a Text display.

Door lock test (locks and unlocks 5 x the door)

Display test (**)

*** ***

None

Sensor test (all wash machine sensors are

tested)

3 3

Reverse

Wash speed (inverse direction high spin)

4 4

Stop

⇒

Standstill motor

5 5

Forward

Wash speed

(same direction high spin)

6 6

Distribute

Distribution speed (same direction high spin)

7 7

Low Extract

Low spin speed

(same direction high spin)

8 8

High Extract

High spin speed

(the drum is turning away from the soap box)

9 9

Stop

Free run or controlled deceleration

The machine takes water by inlet 1

Drain 1

The water is drained by drain valve 1

20 22

The machine takes water by inlet 2 until the

safety level for heating is reached

Heating activated (only if Wait temp = on)

21 23

Drain 1 (2)*

The water is drained by drain valve 1

22 24

The machine takes water by inlet 3

24 26

Supply 1 is activated for 30“

26 28

Supply 2 is activated for 30“

28 30

Supply 3 is activated for 30“

30 32

Supply 4 is activated for 30“

32 34

Supply 5 is activated for 30“

50 50

Tumble

⇒

The tumble sequence

Unload

⇒

End of the Diagnostic Cycle

Note : * The second drain valve will be opened if the second drain valve has been selected in the

Configuration menu.

** For X/XF and MB Door lock test only 1x (X/XF22 5x)

***No number 2 is displayed at the sensor test as this takes only a fraction of a second.

Remark !

If ++ ++ is displayed at the upper right corner of the display at the motor test sequence, then you
can Advance (Press START) the test Sequence.

Summary of Contents for FF10









































































































































Search results

Summary of Contents for FF10

Reviews:

Brands by name

Popular brands

Primus FF10, Programming Manual

Search results

Summary of Contents for FF10

Reviews:

Brands by name

Popular brands