Primus FF10 Programming Manual Download Page 48

Page: 48 / 136

PROGRAMMING MANUAL

100962 G PUBLICATION DATE 24 JUN 2008.DOC

↵

•

If you don‘t want to get in the supply sub-menu, press the

ARROW DOWN button.

•

Press the ENTER button to get into the supply sub-menu.

•

Default: all the supplies are switched off. (time = 0)

•

Liquid soap supplies can only be programmed if the liquid

selection in the configuration menu is enabled.

•

The supplies can be programmed for an interval time

between 0 and 99 seconds.

•

The supply will not be activated if 0 Seconds is programmed.

•

You can program up to 4 supplies at the same time.

If you have programmed more then 4 supplies an error

message will be generated. Put the time of the supplies back

to zero until not more than 4 non-zero time values are

remaining.

•

The overview display shows the Supply Name and the

corresponding programmed time.

•

Insert the desired supply time. Press the ENTER

button for confirmation.

•

At the end of the Menu, when EXIT is displayed, press the

ENTER button to leave the supply Menu.

Attention !

For Top Soap Hopper washing machines, the External liquid

soap pumps correspond with the supplies D to N.

The number of external supplies that is available depends
on the machine type.

•

The wash motor ON time can be programmed between 0 and

99 seconds.

•

The wash motor OFF time can be programmed between 3

and 99 seconds.

•

The suggested default values can be adapted in the

Initialisation menu.

•

Standard wash motor ON time of 12 seconds and a wash

motor OFF time of 3 seconds is recommended for normal

wash. A wash motor ON time of 3 seconds and a wash motor

OFF time of 12 seconds is recommended for a gentle wash

(woolens).

•

Insert the desired ON – OFF times. Press the ENTER

button for confirmation.

•

A PreWash sequence can be programmed between 0 and

99.5 minutes in steps of 0.5 minutes.

•

The default time is 4.0 Minutes.

•

Programming a time of 0 minutes : the Prewash Sequence

will not be functional (cfr No Wash)

P:Pr XX Step XX

Supply ?

P:Pr XX Step XX

On Time : _ _ Sec

P:Pr XX Step XX

Time : 4.0 Min

P:Pr XX Step XX

Off Time: _ _ Sec

P:Pr XX Step XX

Supply A: 0 Sec

P:Soap Supply

Menu Exit

Summary of Contents for FF10









































































































































Search results

Summary of Contents for FF10

Reviews:

Brands by name

Popular brands

Primus FF10, Programming Manual

Search results

Summary of Contents for FF10

Reviews:

Brands by name

Popular brands