Primus FF10 Programming Manual Download Page 67

Page: 67 / 136

100962 G PUBLICATION DATE 24 JUN 2008.DOC

PROGRAMMING MANUAL

↵

configuration menu is enabled. Extra supplies, correspond

with soap pump signals.

•

The Spray Sequence will only function with 1 Supply.

If you have programmed more then 1 supply an error

message will be generated. Put the time of the supplies back

to zero until not more then 1 non-zero time value is

remaining.

•

If a supply has been programmed, no spray inlets can be

programmed.

•

The supplies can be programmed for an interval time

between 0 and 99 seconds.

•

The supply will not be activated if 0 Seconds is programmed.

•

The overview display shows the Supply Name and the

corresponding programmed time.

•

If No supply has been programmed : the Spray sequence will

not be functional (the sequence time must also be 0)

(cfr No Wash).

•

Insert the desired supply time. Press the ENTER

button for confirmation.

•

At the end of the Menu, when EXIT is displayed, you have to

press the ENTER button to leave the supply Menu.

Attention !

For Front Soap Hopper washing machines, the soap is
added by programming the supplies A to E. (X22/5 A to D)

External liquid soap pumps correspond with the supplies

F to K.

For Top Soap Hopper washing machines, the External liquid

soap pumps correspond with the supplies D to J.

The number of external supplies that is available depends
on the machine type.

X & XF - Type machines Only

•

Spray 1 : cold water

•

Spray 2 : warm water

•

The Spray Inlet will be open for the programmed time.

•

Yes : Spray inlet enabled.

No : Spray inlet disabled.

•

Press the ENTER button for confirmation.

X & XF - Type machines Only

•

The Step Time can only be inserted when no supply has

been programmed.

•

The Spray Sequence can be programmed between 0 and 99

P:Pr XX Step XX

Supply A : 0 Sec

P:Pr XX Step XX

Spray 1 : No

P:Pr XX Step XX

Time : 1.0 Min

P:Soap Supply

Menu Exit

P:Pr XX Step XX

Spray 2 : No

Summary of Contents for FF10









































































































































Search results

Summary of Contents for FF10

Reviews:

Brands by name

Popular brands

Primus FF10, Programming Manual

Search results

Summary of Contents for FF10

Reviews:

Brands by name

Popular brands