Primus FF10 Programming Manual Download Page 31

Page: 31 / 136

100962 G PUBLICATION DATE 24 JUN 2008.DOC

PROGRAMMING MANUAL

4.2 CONFIGURATION MENU

This electronic managing system has been specially constructed for a wide range of washing machines. For
that reason it must be individually set up with important parameters for various machine types. Basic
machine adjusting is made in the factory.

WARNING !

ONLY A QUALIFIED TECHNICIAN SHOULD CHANGE THE CONFIGURATION SET UP. AN INCORRECT

CONFIGURATION CAN CAUSE INJURIES AND SERIOUS MACHINE DAMAGE.

HOW TO GET INTO THE CONFIGURATION MENU

The configuration menu can only be accessed when the machine is in standby (the power is switched on, but
no program is started).

1. SELECT Process_ _ is displayed.

Turn the key switch to the program mode.

The Main menu is now available.

Press the ARROW DOWN button to select the Configuration Menu.

Press the ENTER button to make your selection.

For the Configuration Menu a Pass-Word is required.

Insert 3 2 1 and Press the ENTER button

Now you will see the first menu item.

By pressing the ARROW DOWN or UP button you can see the menu items one by one.

•

By pressing the ARROW LEFT or ARROW RIGHT button

you can select the machine type.

•

Check the Machine data plate at the back side of the washing

machine.

•

Press the ENTER button to confirm.

•

As a result you will be asked if you are sure about your

selection.

C: Change Machine type ? No

•

Press the YES and the ENTER button to confirm once more.

•

F22/3= F22 Top soap hopper, F22/5= F22 Front soap hopper

ATTENTION !!!

BE SURE THAT YOU WANT TO ERASE THE OLD SETTINGS, AS THEY CAN’T BE RECAPTURED.

CHANGING THE MACHINE TYPE SHOULD ONLY OCCUR WHEN A NEW FULL CONTROL WASH

COMPUTER IS INSTALLED.

| R7 | R10 | R16 | R22 | R35 | F6 | F7 | F10 | F16 | F22/3 | F22/5 | F33 | F40 | F55 | F120 | X22 |

X35 | X43 | MB26 | MB33 | MB44 | MB66 |

C:Machine type

Main Menu

Configuration

Pass Word _ _ _

Summary of Contents for FF10









































































































































Search results

Summary of Contents for FF10

Reviews:

Brands by name

Popular brands

Primus FF10, Programming Manual

Search results

Summary of Contents for FF10

Reviews:

Brands by name

Popular brands