Primus FF10 Programming Manual Download Page 34

Page: 34 / 136

PROGRAMMING MANUAL

100962 G PUBLICATION DATE 24 JUN 2008.DOC

•

Some machines function with water recovery and are

equipped with a second drain valve.

•

If this second drain valve is a Normal Closed drain valve

then, drain valve 2 must be Selected Yes.

•

Confirm by pressing the ENTER button.

Machines with Front Soap Hopper Only.

•

By selecting “Water Recycle Inlets” Yes its possible to

program 3 extra water inlet valves I4, I5, I6 in the wash

sequences and 3 extra outlet valves for water recycling

combined with pump in the drain-extraction sequences.

•

No is the default value.

•

Yes : Extra water recycle Inlets and Outlets can be selected

in the Program menu’s.

No : Extra water recycle Inlets and Outlets are switched off

in the Program menu’s.

•

Confirm by pressing the ENTER button.

Attention !

In some machines extra electrical components have to be
added as an option to complete the electrical installation.

Only for washing machines with Front Soap Hopper.

•

If the operator doesn‘t want to use the Soap Hoppers and

has connected the electrical signal of the hopper to an

external liquid soap supply pump, the signal must be set on

Liquid.

•

Liquid can be selected by pressing the ARROW Right

button.

•

Supply Sign A corresponds with the First soap hopper.

Supply Sign B corresponds with the Second soap hopper.

…

Supply Sign E corresponds with the Fifth soap hopper.

•

By selecting liquid, no pulse will interrupt the soap supply

signal.

•

Confirm by pressing the ENTER button.

C:Drain

Valve 2: No

C:Supply Sign

A: Hopper

C:Water Recycle

Inlets : No

Summary of Contents for FF10









































































































































Search results

Summary of Contents for FF10

Reviews:

Brands by name

Popular brands

Primus FF10, Programming Manual

Search results

Summary of Contents for FF10

Reviews:

Brands by name

Popular brands