Primera Digital Color Label Press CX1200e Operation Manual Download Page 11 | Manualshive

Page: 11 / 65

background image

6 Unpack and Assemble

9. Place the printer on the base. Primera recommends three people to lift the printer on top of the

base. Two people are required to lift the printer and one person to guide the printer onto the
mounting pegs. Align the pegs on the base with the holes in the bottom of the printer. Use the
locating label to align the right front edge of the printer with indicated mark on the label. The
front edge of the printer will be 63.5 mm (2.5 inches) from the front of the base.

10. Now that the printer is in place, all of the packing tape, clips and shipping protection devices

must be removed. First remove the tape securing the front cover.

Figure 2-9.

Figure 2-10.

63.5 mm (2.5 inches)

«
...
9
10
11
12
13
...
»

Summary of Contents for Digital Color Label Press CX1200e


































































Reviews:

No comments

Related manuals for Digital Color Label Press CX1200e

Brand: Panasonic Pages: 30

Brand: Panasonic Pages: 28

Bread Bakery SD-YD250

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 44

Bread Bakery SD-YD250

Brand: Panasonic Pages: 37

Bread Bakery SD-BT2P

Brand: Panasonic Pages: 11

Brand: Haden Pages: 9

Brand: Bartscher Pages: 86

Brand: FlyTek Pages: 24

Brand: Clatronic Pages: 42

Brand: Ice-O-Matic Pages: 2

Brand: La Cimbali Pages: 43

Brand: Unit Pages: 56

Brand: Russell Hobbs Pages: 8

ALPATEC MG 12 LEGEND

Brand: Taurus Pages: 60

Brand: Witt Pages: 132

Brand: Dymo Pages: 36

Brand: Candi Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands