Primera Digital Color Label Press CX1200e Operation Manual Download Page 35 | Manualshive

Page: 35 / 65

background image

30 Create a Print File

5. Below is an example of edge sensitivity set too low. Notice how the contour line invades the

image on the left side. This is because the image is very light in that area.

6. To retry the edge detection simply click Apply again.

Note:

The object must stay selected for the

contour toolbar and the apply button to be visible. If it is not visible, repeat steps 1-2.

7. This time, enter a higher value in the threshold window. You may have to repeat this procedure

a few times.

If the cut lines are not smooth,
you may also adjust the Trace
Setup drop down menu.
Typically, Script Text or
CutContour are the best options.

«
...
33
34
35
36
37
...
»

Summary of Contents for Digital Color Label Press CX1200e


































































Reviews:

No comments

Related manuals for Digital Color Label Press CX1200e

I-Class Mark II

Brand: Datamax Pages: 74

AromaElegance Therm

Brand: Melitta Pages: 46

Brand: Saeco Pages: 100

Brand: SOLAC Pages: 36

Brand: inventum Pages: 40

Brand: Vitek Pages: 40

Brand: Scarlett Pages: 16

Brand: Klarstein Pages: 36

Brand: Moulinex Pages: 56

Brand: Dalla Corte Pages: 60

Brand: Laspaziale Pages: 36

Brand: N&W Global Vending Pages: 72

Brand: Manitowoc Pages: 264

Brand: Oki Pages: 140

Brand: Philips Pages: 24

Brand: Oster Pages: 46

Brand: Oster Pages: 18

Brand: Oster Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands