35
CO
M
CO
M
CO
M
24
V
AC 24
V
AC
AL
T
RDO OP
N
CRO
FR
E
OP
N
CL
O
ST
O
CO
M
CO
M
CO
M
OP
N
PH
O
CL
O
PH
O
SH
W
RE
V
OP
N
ED
G
CL
O
ED
G
MS
T
OP
N
MS
T
CL
O
CO
M
CO
M
CO
M
OPEN
PUSH
FREE
EXT
ALT
RADIO
OPN/
CLO
RADIO
OPEN
CLOSE
PUSH
STOP
PUSH
CLOSE
PHOTO
OPEN
PHOTO
LD1 8
LD1 0
LD1 1
LD1 2
LD1 5
LD1 4
LD1 6
LD1 7
LD1 3
OPEN
CLOSE
STOP
OPEN
CLOSE
FORCE
ADJUSTMENT
AUTO
RECLOSE
TIMER
OFF MAX
MID
LIMIT
REV
LOOP
OPN
EDGE
CLO
EDGE
RH OPN
LH CLO
LIMIT
RH CLO
LH OPN
LIMIT
MOTOR
OPEN
MOTOR
CLOSE
SHADOW
LOOP
LD19
LD2
LD3
LD4
LD5
LD6
LD8
LD9
LD7
1 2 3 4 5
POWER
LD1
P3
P4
TB 1
TB 2
U1
U2
U4
ALT
RADIO
OPN/
CLO
RADIO
OPEN
CLOSE
PUSH
STOP
PUSH
LD11
LD12
LD15
LD14
LD16
LD17
OPEN
CLOSE
STOP
OPEN
1 2 3 4 5
ON
OFF
1 2 3 4 5
ON
OFF
For Normally
Open Stop
Button
For Normally
Closed Stop
Button
BOARD MOUNTED CONTROL STATION
If Dipswitch #3 is in the “OFF” position, the board mounted
three button station will function normally.
6. If the gate travels in the correct direction and stops on
the open limit switch, proceed to step #10.
NOTE:
Open and Close Limit Switches are
Reversed
for
Slide Left to Open Operation
.
Pressure
Plate
Limit Nut
CLOSE LIMIT SWITCH
for slide right to open
operation
Limit Shaft
Limit Nut
OPEN LIMIT SWITCH
for slide right to open
operation
NOTE:
If Dipswitch #3 is in the
“ON”
position for use with a
NORMALLY CLOSED “STOP”
BUTTON,
then the board mounted
“STOP” button must be held
depressed in order to use the open
and close buttons. Releasing the stop
button will then stop the operator.
36
7. If the operator runs in the wrong direction proceed to
step #9.
8.
If the limit nut depresses the open limit switch but does not
stop the gate, press the stop button or turn off the power
immediately, and consult factory.
(1-800-243-4476).
9.
Check position of dipswitch #2 to be sure it coincides with
the installation. (Left Hand or Right Hand) If this is correct
consult the factory. (1-800-243-4476).
10. If the operator functions properly, run the operator to
the open limit switch and turn off the power.
11. If there is still a distance before the gate is fully open,
turn off power, move the open limit nut away from the
open limit switch a few turns and turn on the power.
12. Press the OPEN button again to check how much
further the gate opened.
13. Continue this procedure until the OPEN limit is set.
NOTE:
When making fine adjustments, turn the limit nut one
quarter turn at a time; reconnect power and test run the
gate.
14. Repeat procedure for the CLOSE limit adjustment.
15. After the desired open and close position of the gate
has been obtained, make certain that a groove in both
limit nuts are engaged by the pressure plate.
