manualshive.com logo in svg

Power Computing PowerWave 604, User Manual

Share
Download
Power Computing PowerWave 604 User Manual Download Page 67

 

For Technical Support, Call 1-800-708-6227

 

PowerWave 604 UserÕs Guide   

 

47

 

4

 

Connecting Peripheral 
Devices

 

4

 

Your computer has a number of ports for connecting peripheral devices such as printers, 
storage devices, audio equipment, network cabling, and modems.

See ÒPowerWave 604 OverviewÓ on page ix at the beginning of this manual for the location 
of the ports.

 

Using SCSI devices 

 

Your computer has two separate SCSI busesÑone for the internal devices like the hard disk 
and the optional CD-ROM drive and another for external devices. You can connect up to 
seven devices in a 

 

SCSI chain

 

 to each bus. 

Connecting a SCSI device involves four steps:

 

■

 

Setting the deviceÕs SCSI ID number

 

■

 

Ensuring proper termination

 

■

 

Connecting the device

 

■

 

Installing a software device driver (if one is required)

 

Setting the SCSI ID

 

Each device in a SCSI chain requires a unique number called a SCSI ID, which the computer 
uses to identify the device. The computer itself is assigned SCSI ID 7 and the internal hard 
disk is assigned SCSI ID 0. Every other device you install must have a unique number from 
1 to 6. An optional hard drive is normally assigned a SCSI ID of 1, a tape drive is normally 
assigned 2, and a CD-ROM drive or removable-media drive is normally assigned SCSI ID 3. 

Devices on the external bus must have a unique SCSI ID from 0 to 6.

The way you assign SCSI IDs varies from device to device. On most external devices, the ID 
is displayed on the back of the device. You usually change it by pressing small buttons above 
or below the number display. For some external and most internal devices, changing the ID 
requires setting switches or moving jumpers. Refer to the documentation that came with the 
device for exact instructions.

 

Chapter

Summary of Contents for PowerWave 604





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands