Pottinger Profi Gp 1 Operating Instructions Manual Download Page 34 | Manualshive

Page: 34 / 54

background image

GB

TAIL GATE

- 34 -

9500 GB RÜCKWAND (511)

Safety tip

Adjusting the relieving spring

The operating force on lever (A) should not exceed
25 kp (245 N).

From there adjust the relieving spring tension (Z)
accordingly.

Adjustments

So that the opening and closing of the tail gate functions properly, set the adjusting screws left and
right according to the following sequence.

- Turn the hexagonal screw (57) until the lower pipe of the tail gate fits into the slotted plate (K).

TD56/94/5

max.

25 kp

Z

«
...
32
33
34
35
36
...
»

Summary of Contents for Profi Gp 1























































Reviews:

No comments

Related manuals for Profi Gp 1

Brand: Watt Drive Pages: 54

Brand: a-TroniX Pages: 92

Brand: Panasonic Pages: 38

Brand: Barco Pages: 4

Brand: Velleman Pages: 28

Brand: GME Pages: 21

Brand: Gbxpoint Pages: 4

Brand: N-Tron Pages: 40

FRN0001C2S-2A FRN0002C2S-2A FRN0004C2S-2A FRN0006C2S-2A FRN0010C2S-2A FRN0012C2S-2A FRN0020C2S-2A FRN0025C2S-2A FRN0033C2S-2A FR

Brand: Fuji Electric Pages: 263

Brand: AceWav Pages: 2

Giga-MiniMC 856-10730-RX

Brand: B&B Electronics Pages: 15

Brand: ENC Pages: 57

Brand: Chord Pages: 2

Brand: Growatt Pages: 25

Brand: FBS Pages: 6

Brand: KONANlabs Pages: 6

Brand: Cross Technologies Pages: 18

SinePower SP150

Brand: Waeco Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands