Pottinger Profi Gp 1 Operating Instructions Manual Download Page 3

Page: 3 / 54

Dokument

GB-0100 Dokum D Anhänger

- 3

ALOIS PÖTTINGER Maschinenfabrik GmbH
A-4710 Grieskirchen
Tel. (07248) 600 -0
Telefax (07248) 600-511

GEBR. PÖTTINGER GMBH
D-86899 Landsberg/Lech, Spöttinger-Straße 24
Telefon (0 81 91) 92 99-111 / 112
Telefax (0 81 91) 92 99-188

GEBR. PÖTTINGER GMBH
Servicezentrum
D-86899 Landsberg/Lech, Spöttinger-Straße 24
Telefon (0 81 91) 92 99-130 / 231
Telefax (0 81 91) 59 656

❑

Machine checked according to delivery note. All
attached parts removed. All safety equipment, drive
shaft and operating devices at hand.

❑

Operation and maintenance of machine and/or
implement according to operating instructions
explained to the customer.

❑

Tyres checked re. correct pressure.

❑

Wheel nuts checked re. tightness.

❑

Drive shaft cut to correct lenght.

❑

Correct power-take-off speed indicated.

❑

Mechanical functions (opening of rear gate, pivoting
of cutting mechanism out/in, etc.) demonstrated and
explained.

❑

Removing and mounting of knives explained.

❑

Electrical connection to tractor established and
checked re. correct supply (54 g connected). Note
references in operating manual.

Please check.

According to the product liability please check the above mentioned items.

INSTRUCTIONS FOR
PRODUCT DELIVERY

❑

Fitting to tractor carried out: hight of drawbar adjusted,
brake cable installed, hand brake lever assembled in
tractor cabin.

❑

Function of electrical installation checked and
explained.

❑

Hydraulic connection to tractor established and checked
re. correct supply.

❑

Hydraulic functions (drawbar, opening of rear gate, etc.)
demonstrated and explained.

❑

Handbrake and operating brake tested re. function.

❑

Trial run carried out and no defects found.

❑

Functions explained during trial run.

❑

Automatic on/off switch of loading mechanism checked.

❑

Pivoting in transporting and operating position
explained.

❑

Information given re. optional extras.

❑

Absolute need to read the operating manual indicated.

In order to prove that the machine and the operating manual have been properly delivered, a confirmation is necessary.
For this purpose please do the following:
-

sign the

document A

and send it to the company Pöttinger

(in case of Landsberg equipment: to the company Landsberg)

document B

stays with the specialist factory delivering the machine.

document C

stays with the customer.

Summary of Contents for Profi Gp 1























































Search results

Summary of Contents for Profi Gp 1

Reviews:

Related manuals for Profi Gp 1

Brands by name

Popular brands

Pottinger Profi Gp 1, Operating Instructions Manual

Search results

Summary of Contents for Profi Gp 1

Reviews:

Related manuals for Profi Gp 1

Brands by name

Popular brands