Pottinger Profi Gp 1 Operating Instructions Manual Download Page 12

Page: 12 / 54

COUPLING AND UNCOUPLING THE TRAILER

- 12 -

537 / AN- U. ABKUPPELN 9500 GB

Safety Cable

(max. 25 km und max. 4 to zul. Ges Gew.)

- Safety cable (6) to be fitted

correctly to tractor's towing
coupler. (Safeguard against
breakage of trailer coupling
ring or detachment from
tractor.)

Abreißseil

(nur bei

Auflaufbremsanlage)

- Bei Anhänger mit

Auflaufvorrichtung das
Abreißseil (1) vom
Handbremshebel am
Traktor verknoten.

(Safeguard against
breakage of trailer
coupling ring or
detachment from
tractor.)

Drive shaft adaption

To shorten the drive shaft see supplement-B!

Hydraulic connection

- Connect hydraulic lines to tractor.

• See also chapter

"HYDRAULIC OPERATION",

"ELECTROHYDRAULIC OPERATION".

Putting into operation

• Before putting the tractor or implement into operation check

vehicle safety (lights, brake unit, protective covering …)!

• Pay attention to correct load distribution during operation!

Uncoupling and parking the trailer

• See also chapter

"SUPPORTING WHEEL", "BRAKE

UNIT", "DRAWBAR".

Important!

Before uncoupling the snap-lock coupler

1. Raise the pick-up.

2. Close shut-off valve on snap-lock coupler (position A).

3. Release pressure on tractor's control unit (ST) and uncouple.

Attention!

• Always park implement so that it is standing safety.

• Secure trailer against rolling away (locking brake, wedges).

Parking in the open

When parking for longer
periods in the open, clean
plunger rods and then coat
with grease.

Garaging for winter

- Thoroughly clean the machine before garaging for winter.

- Apply weather protection.

- Change or top-up gear oil.

- Protect uncoated parts against rusting.

- Grease all lubricating points according to lubrication chart.

FETT

TD49/93/2

TD31/90/21

Summary of Contents for Profi Gp 1























































Search results

Summary of Contents for Profi Gp 1

Reviews:

Related manuals for Profi Gp 1

Brands by name

Popular brands

Pottinger Profi Gp 1, Operating Instructions Manual

Search results

Summary of Contents for Profi Gp 1

Reviews:

Related manuals for Profi Gp 1

Brands by name

Popular brands