Pottinger Profi Gp 1 Operating Instructions Manual Download Page 7

Page: 7 / 54

- 7 -

511 / STÜTZRAD 9800-GB

SUPPORTING WHEEL

Operating the swivelling supporting wheel

Only use eccentric lever (1) when implement is hitched
to tractor (danger of an accident should the trailer tip
sideways)! Therefore keep children away from the
parked trailer.

Hitching up the implement

1. Couple implement to tractor and

wind up supporting

wheel

2. Unlock positioning bolts

with eccentric lever (1).

3. Swivel supporting

wheel up and secure.

Support wheel must not protrude beyond
external contour of tractor!
Wind supporting wheel completely up!

Parking the implement

• Park the trailer on firm, level ground.

If the ground is soft then the area where the support
wheel is to stand must be appropriately increased using
a suitable aid (e.g. wooden board).

• Park only empty implement on supporting wheel!
• When trailer is parked, apply the brake and secure

against rolling with wheel chocks.

1. Using eccentric lever (1) raise supporting wheel slightly and

unlock.

2. Swivel supporting wheel

down and lock using
eccentric lever (1).

Engaging positioning bolts
can be visually discerned
using safety rod (2).

3. Turn supporting wheel crosswise inwards.

4. Wind implement up until tow ring is clear of tractor's coupling.

Maintenance advice

Grease locking bolts occasionally!

Summary of Contents for Profi Gp 1























































Search results

Summary of Contents for Profi Gp 1

Reviews:

Related manuals for Profi Gp 1

Brands by name

Popular brands

Pottinger Profi Gp 1, Operating Instructions Manual

Search results

Summary of Contents for Profi Gp 1

Reviews:

Related manuals for Profi Gp 1

Brands by name

Popular brands