Potterton Eurocondense three Programming Manual Download Page 77

Page: 77 / 120

The following messages are possible under

boiler

End user (E)

Commissioning, Technician (menu

state

)

SLT has tripped

SLT test active

Fault

Flue gas temp too high

Flue gas temp, shutdown

Flue gas temp, powerlimitation

Monitor has tripped

Manual control active

Chimney sweep funct active

Chimney-sweep function, nominal load

Chimney-sweep function, part load

Locked

Locked, manual

Locked, solid fuel boiler

Locked, automatic

Locked, outside temp

Locked, economy mode

Min limitation active

Min limitation

Min limitation, part load

Min limitation active

In operation

Protective start

Protective start, part load

Return limitation

Return limitation, part load

Charging buffer

In op for HC, DHW

In part load op for HC, DHW

Released for HC, DHW

In operation for DHW

In part load op for DHW

Released for DHW

In operation for HC

In part load op for HC

Released for HC

Overrun active

Released

Frost protection active

Frost prot plant active

Off

Programming

358 488 09.10

Gas-fired fuel value boiler EuroCondense three 125-300 kW

Summary of Contents for Eurocondense three

























































































































Search results

Summary of Contents for Eurocondense three

Reviews:

Potterton Eurocondense three, Programming Manual, Page: 77 / 120

Search results

Summary of Contents for Eurocondense three

Reviews: