manualshive.com logo in svg

Potterton Eurocondense three, Programming Manual, Page: 76 / 120

Share
Download
Potterton Eurocondense three Programming Manual Download Page 76

The following messages are possible under 

DHW

:

End user (E)

Commissioning, Technician (menu 

state

)

Monitor has tripped

Monitor has tripped

Manual control active

Manual control active

Consumption

Consumption

Holding mode On

Holding mode Active

 

Holding mode On

Recooling active

Recooling via collector

 

Recooling via heat gen

 

Recooling via HCs

Charging lock active

Discharging prot active

 

Charg time limitation active

 

Charging locked

Forced charging active

Forced, max stor tank temp

 

Forced, max charging temp

 

Forced, legionella setp

 

Forced, nominal setp

Charg el imm heater

El charging, legionella setp

 

El charging, nominal setp

 

El charging, reduced setp

 

El charging, frost prot setp

 

El imm heater released

Push active

Push, legionella setp

 

Push, nominal setp

Charging active

Charging, legionella setp

 

Charging, nominal setp

 

Charging, reduced setp

Frost protection active

Frost protection active

 

Frost protection Instantaneous water

heater

Overrun active

Overrun active

Standby charging

Standby charging

Charged

Charged, max st tank temp

 

Charged, max charging temp

 

Charged, legionella temp

 

Charged, nominal temp

 

Charged, reduced temp

Off

Off

Ready

Ready

Programming

76

Gas-fired fuel value boiler EuroCondense three 125-300 kW

358 488 09.10

Summary of Contents for Eurocondense three

























































































































Reviews:

No comments