manualshive.com logo in svg

Potterton Eurocondense three, Programming Manual, Page: 65 / 120

Share
Download
Potterton Eurocondense three Programming Manual Download Page 65

-

Status output K35

: The status output will be operated when a command exists

from the controller to the firing automation. If there is a disturbance, which pre-

vents the firing automation to operate, the status output will be switched off.

-

Status information K36

: The output is set, when the burner operates.

-

Flue gas damper K37

: This function activates the flue gas damper control. If the

flue gas damper control is activated the burner will only start operating, when

the flue gas damper is open.

-

Fan shutdown K38

: This output serves to stop the fan. The output is activated,

when the fan is needed; otherwise it is not activated. The fan should be swit-

ched off as often as possible, to minimize the total energy consumption of hte

system.

Sensor inputs BX1/BX2/BX3

(5930 - 5932)

  Functions in addition to the basic functions will be possible by configuring the

sensor inputs.

-

None

: Sensor inputs deactivated.

-

DHW sensor B31

: second DHW sensor, which is used for through loading of the

legionella function.

-

Collector sensor B6

: first solar collector sensor in a collector field.

-

DHW circulation sensor B39

: Sensor for return line of DHW circulation.

-

Buffer st tank sensor B4

: lower buffer storage tank sensor.

-

Buffer st tank sensor B41

: centre buffer sensor.

-

Flue gas temp sensor B8

: Flue gas temp sensor for the alarmfunction.

-

Common flow sensor B10

: common flow sensor for boiler cascades.

-

Solid fuel boiler sensor B22

: Sensor for the acquisition of the temperature of a

solid fuel boiler.

-

DHW charging sensor B36

: DHW sensor for DHW charging system.

-

Buffer st tank sensor

: upper buffer storage tank sensor.

-

Common return sensor B73

: Return sensor for the function return diversion.

-

Cascade return sensor B70

: common return sensor for boiler cascades.

-

Swimming pool sensor B13

: Sensor for measurement of swimming pool temp.

-

Solar flow sensor B63

: this sensor is required for the solar usage measurement.

-

Solar return sensor B64

: this sensor is required for the solar usage measure-

ment.

Function inputs H1/H4/H5/

H2

(5950, 5970, 5977)

  -

None

: No function.

-

Optg mode change HCs+DHW

: Changeover of the operating modes of the hea-

ting circuits to reduced operation or protecting operation (program numbers

900, 1200, 1500) and locking of domestic hot water charging in case of closed

contact at H1/H4/H5/H2.

-

Optg mode changeover HC1 to HC3

: Changeover of operating modes of the hea-

ting circuits to protective operation or reduced operation.

Locking of domestic hot water charging is only possible under the setting 

Optg

mode change HCs+DHW

.

Programming

358 488 09.10

Gas-fired fuel value boiler EuroCondense three 125-300 kW

65

Summary of Contents for Eurocondense three

























































































































Reviews:

No comments