Polaris RANGER RZR 170 Service Manual Download

Page: 25 / 231

2.9

MAINTENANCE

9923983 - 2012-2013 RZR 170 Service Manual

MAINTENANCE REFERENCES

* More often under severe use, such as operated in water or under severe loads.

**Semi-annually or 50 hours of operation (refer to Maintenance Schedule for additional information)

***Annually or 100 hours of operation (refer to Maintenance Schedule for additional information)

Item

Ref.

Rec. Lube / Fluid

Method

Frequency*

Engine Oil

Page 2.7

Performance Synthetic

(PS-4) Extreme Duty Oil

Add oil to proper level on

dipstick.

Change after 10 hrs, and

then every 50 hours, 6

months or 100 hours

thereafter; Change more

often in extremely dirty

conditions, or short trip

cold weather operation.

Brake Fluid

Page 2.7

DOT 4 (PN 2872189)

Fill reservoir between

MAX and MIN lines.

Fill as required. Change

brake fluid every 2 years.

Transmission

Page 2.7

AGL Plus Synthetic

Gearcase

Lubricant (PN 2873602)

Add lube to bottom of fill

plug threads. 24 oz. (710

ml)

Change annually***

Front A -Arm

and Steering

Pivot Bushings

Page 2.6

Polaris Premium All

Season Grease (PN

2871423)

Locate grease fittings and

grease with grease gun.

Semi-annually**

Summary of Contents for RANGER RZR 170




























































































































































































































Search results

Summary of Contents for RANGER RZR 170

Reviews:

Related manuals for RANGER RZR 170

Brands by name

Popular brands

Polaris RANGER RZR 170, Service Manual

Search results

Summary of Contents for RANGER RZR 170

Reviews:

Related manuals for RANGER RZR 170

Brands by name

Popular brands