Platinum Access Systems BLSL2250 Installation Instructions & Owner'S Manual Download Page 18 | Manualshive

Page: 18 / 36

background image

16

TECHNICAL SUPPORT: (909) 259-6001

BLSL2250

Installation: Alarm Reset Switch & Warning Placards

ALARM RESET SWITCH INSTALLATION:

(UL 325 standard requirement)

$QDODUPVKDOOVLJQDOXSRQWZRVHTXHQWLDODFWLYDWLRQVRIDQHQWUDSPHQWSURWHFWLRQGHYLFHZKHUHWKH¿UVWDFWLYDWLRQ

is either a Type A or B2 device and the second activation is a Type A device. The alarm shall signal for a minimum

of 5 min or until a renewed manual input from an integral control or a permanently mounted control (such as a Stop

button) located in the line-of-sight of the gate has been entered. An audio alarm is not required for Classes III and IV.

To reset the alarm the Stop command can be given in two different ways.

1- The Built in Stop switch on the control board.

2- The External Stop button in the line-of-sight of the gate, away from moving parts of the gate and out of

reach of children.

WARNING PLACARDS INSTALLATION:

WARNING – To reduce the risk of severe injury or death to person, please follow these instructions:

All Warning Sings and Placards must be mounted where visible in the area of the gate.

A minimum of two (2) Warning Placards shall be mounted. (One on each side of the gate).

Out of Reach

6'

5'

Minimum

Manual Stop

Button

COM

N.C.

STOP

STOP

BLSL2250 Manual_Layout 1 2/10/2014 4:40 PM Page 18

«
...
16
17
18
19
20
...
»

Summary of Contents for BLSL2250





































Reviews:

No comments

Related manuals for BLSL2250

Brand: Wayne-Dalton Pages: 20

Brand: Wayne-Dalton Pages: 4

Brand: Wayne-Dalton Pages: 22

Eagle-2000 series

Brand: Eagle Access Control Systems Pages: 26

Brand: Avidsen Pages: 8

Brand: Teckentrup Pages: 76

Brand: fadini Pages: 36

Brand: Jaytech Pages: 21

Brand: Elite Pages: 23

Premium Slider 500

Brand: BelFox Pages: 136

Brand: BelFox Pages: 160

Brand: FAAC Pages: 9

Brand: fadini Pages: 24

Brand: DACE Pages: 12

TorqueMaster Plus 9800

Brand: Wayne-Dalton Pages: 38

Torsion 7100 Series

Brand: Wayne-Dalton Pages: 16

Brand: Henderson Pages: 2

Brand: Linear Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands