Platinum Access Systems BLSL2250 Installation Instructions & Owner'S Manual Download

Page: 4 / 36

TECHNICAL SUPPORT: (909) 259-6001

BLSL2250

Gate operator class categories and examples

HOTEL

FACTORY

DOCK

HANGAR 00

READ AND FOLLOW ALL INSTRUCTIONS MANUAL BEFORE ATTEMPTING

ANY INSTALLATION

Residential Vehicular Gate Operator

Class I

A vehicular gate operator (or system) intended

for use in a home of one-to four single family

dwelling, or a garage or parking area associated

therewith.

Commercial/General Access

Vehicular Gate Operator

Class II

A vehicular gate operator (or system) intended

for use in a commercial location or building such

DVDPXOWLIDPLO\KRXVLQJXQLW¿YHRUPRUHVLQJOH

family units), hotel, garages, retail store, or other

building servicing the general public.

Industrial/Limited Access Vehicular

Gate Operator Class III

A vehicular gate operator (or system) intended for

use in an industrial location or building such as

a factory or loading dock area or other locations

not intended to service the general public.

Restricted Access Vehicular Gate

Operator

Class IV

A vehicular gate operator (or system) intended

for use in a guarded industrial location or building

such as an airport security area or other restricted

access locations not servicing the general public,

in which unauthorized access is prevented via

supervision by security personnel.

BLSL2250 Manual_Layout 1 2/10/2014 4:40 PM Page 4

Summary of Contents for BLSL2250





































Search results

Summary of Contents for BLSL2250

Reviews:

Related manuals for BLSL2250

Brands by name

Popular brands

Platinum Access Systems BLSL2250, Installation Instructions & Owner'S Manual

Search results

Summary of Contents for BLSL2250

Reviews:

Related manuals for BLSL2250

Brands by name

Popular brands