Platinum Access Systems BLSL2250 Installation Instructions & Owner'S Manual Download | Manualshive

Page: 15 / 36

background image

TECHNICAL SUPPORT: (909) 259-6001

BLSL2250

13

Installation: entrapment protection

Contact Sensor Installation:

Only sensors compliant with UL 325 are recommended.

Contact

Sensor

Contact

Sensor

All Contact Sensors to

be wired in parallel

Non-Contact Sensors (Photoelectric Sensors) Installation:

One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists,

such as the perimeter reachable by a moving gate or barrier.

Install photoelectric sensors to protect

against any entrapment or safety conditions

encountered in your gate application.

We recommend the use of EMX IRB-325

photoeyes to comply with UL325.

Gate in Closed Position

Photo Beam

Unit

Reflector

Contact Sensor

Contact

Sensor

Potential Entrapment Area

Note: This type of installation DOES NOT reverse the gate all the way back to its limits when the sensors

are obstructed. This installation is only to protect against entrapment and to comply with UL325.

TX

EMX Model

IRB-325

Shown

Connection ‘1’ (C1)

Connection ‘2’ (NC1)

Consult the UL325 device installation manual for more detail information about the usage,

installation and maintenance of this device.

BLSL2250 Manual_Layout 1 2/10/2014 4:40 PM Page 15

«
...
13
14
15
16
17
...
»

Summary of Contents for BLSL2250





































Reviews:

No comments

Related manuals for BLSL2250

Brand: FAAC Pages: 27

Brand: FAAC Pages: 14

Brand: Liftaway Pages: 19

Brand: CAME Pages: 32

Frankling Autoswing

Brand: Real Carriage Door & Sliding Hardware Pages: 56

Brand: Viking Pages: 44

Brand: Ginnys Pages: 8

Brand: Craftsman Pages: 8

Brand: Nice Pages: 44

Brand: CAME Pages: 2

Brand: CAME Pages: 16

Security+ 1210E FS2

Brand: Chamberlain Pages: 80

Brand: Rival Pages: 4

GOLD400D Series

Brand: V2 Pages: 172

Brand: Gatekeeper Pages: 32

Brand: GATEXPERT Pages: 34

Brand: Chamberlain Pages: 44

Brand: tau Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands