Platinum Access Systems BLSL2250 Installation Instructions & Owner'S Manual Download Page 19 | Manualshive

Page: 19 / 36

background image

TECHNICAL SUPPORT: (909) 259-6001

BLSL2250

17

Installation: ElecTrical

Ground Rod

Earth Ground

- (Green)

Earth Ground (Green/Yellow)

+ (White)

Hot (Black)

Neutral (White)

To Power Harness

power cable to the board. USE MIN. 14 AWG WIRE. FOLLOW ALL LOCAL ELECTRICAL CODES.

Power Harness

White

Green

Red

Black

To help protect the equipment from lightning and power
surges and to protect persons from shock hazard the
Operator  must  be  grounded.  The  earth  ground  rod
must be located within 3 feet from the gate operator.
Use  the  proper  type  earth  ground  rod  for  your  local
area. The ground wire must be a single, whole piece of
wire. Never splice two wires for the ground wire. If you
cut  the  ground  wire  too  short,  break  it,  or  destroy
its  integrity,  replace  it  with  a  single  wire  length.
Prevent  unnecessary  turns  or  loops  in  ground  wires.

The gate operator and the battery charger require a
single phase AC line to operate.

1.  Turn off the breaker for the circuit you are using.
2.  Select the proper voltage on the power board.
3.  Connect the incoming power wires to the proper
  terminals.
4.  Turn on the breaker and check that AC ON and
  CHARGE LED are lit.

The power receptacle has been left unconnected till the installer decides what voltage to use.
Connect to 120VAC only

BLSL2250 Manual_Layout 1 2/10/2014 4:40 PM Page 19

«
...
17
18
19
20
21
...
»

Summary of Contents for BLSL2250





































Reviews:

No comments

Related manuals for BLSL2250

Brand: Daspi Pages: 16

Brand: Daspi Pages: 14

Brand: Aprimatic Pages: 3

Brand: Motorline Pages: 35

Brand: Novoferm Pages: 32

Brand: B&B ARMR Pages: 24

Brand: Proteco Pages: 10

Brand: JOYTECH Pages: 18

Brand: DITEC Pages: 16

Brand: MAG Pages: 9

Brand: FAAC Pages: 19

Brand: FAAC Pages: 19

Brand: Alutech Pages: 40

Brand: Roger Technology Pages: 49

BRUSHLESS B70/2DC

Brand: Roger Technology Pages: 116

Brand: FAAC Pages: 32

Brand: Beninca Pages: 20

Brand: Reisinger Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands