background image

TECHNICAL SUPPORT: (909) 259-6001

BLSL2250

3

PROTECTION AGAINST ENTRAPMENT

 

 

  

 

 

     

 

 

 

Usage Class

Gate Operator Category

Horizontal Slide, Vertical lift, and Vertical Pivot

Swing and Vertical Barrier (arm)

Primary Type*

Secondary Type*

Primary Type*

Secondary Type*

Vehicular I and II

Vehicular III

Vehicular IV

A

A, B1, or B2

A, B1, B2, or D

B1, B2, C, or D

A, B1, B2, C, D, or E

A, B1, B2, C, D, or E

B1, B2, or D

A, B1, B2, D, or E

A, B1, B2, D, or E

A, or C

A, B1, B2, or C

A, B1, B2, C, or D

Note  -  The  same  type  of  device  shall  not  be  utilized  for  both  the  primary  and  the  secondary  entrapment 

protection means. Use of a single device to cover both the opening and closing directions is in accordance with 

the requirement; however, a single device is not required to cover both directions. A combination of one Type 

B1 for one direction and one Type B2 for the other direction is the equivalent of one device for the purpose of 

complying with the requirements of either the primary or secondary entrapment protection areas.

Entrapment protection Types:

Type A:

  Inherent entrapment protection system.

Type B1:

 Provision for connection of, supplied with, a non-contact sensor (photoelectric sensor  

 

or the equivalent).

Type B2:

 Provision for connection of, or supplied with, a contact sensor (edge device or the equivalent)

Type C:

  Inherent adjustable clutch or pressure relief device.

Type D:

  Provision for connection of, or supplied with, an actuating device requiring continuous pressure to 

 

maintain opening or closing motion of the gate.

Type E:

  An audio alarm.

BLSL2250 Manual_Layout 1  2/10/2014  4:40 PM  Page 5

Summary of Contents for BLSL2250





































Reviews: