manualshive.com logo in svg

Planar Dome Md2/PCI, Installation Manual

Share
Download
Planar Dome Md2/PCI Installation Manual Download Page 13

 

 About This Guide |

 

 

xiii

 

What’s in this guide

 

This table describes the organization of this guide.

 

Related documentation

 

For more information about the board and its driver, 
related DOME products, or your operating system, 
refer to these books:

 

• PCI Products Developer’s Guide

• DIMPL Library Reference

• DimplX ActiveX Control Reference

• DimFileX ActiveX Control Reference

 

• Microsoft documentation

• Sun documentation

 

This chapter…

Describes…

 

Chapter 1

Planning the Board 
Installation

An overview of the Md2/PCI board, 
including features and installation 
requirements

Chapter 2

Installing the Board and 
Driver in a PC

Instructions for installing and configuring 
the Md2/PCI board and its Windows 2000 
or Windows NT driver in a PC

Chapter 3

Installing the Board and 
Driver in a Sun PCI 
Workstation

Instructions for installing and configuring 
the Md2/PCI board and its Solaris driver 
in a Sun PCI workstation

Appendix

Board Resolutions and 
Refresh Rates

Resolutions and refresh rates supported 
by the Md2/PCI board in PCs and Sun 
PCI workstations

Summary of Contents for Dome Md2/PCI





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands