Pitney Bowes OFFICERIGHT DI200 Operator'S Manual Download Page 38

Page: 38 / 49

Offi ceRight™ DI200 Operator Guide (SV41289-OG Rev. C)

Reference

Message

Meaning and Action

REMOVE ALL

This could be due to a material jam in fold plate 1 or

FROM D & E

near the insertion area. Open front cover D and remove

any material that’s there. Close cover D. Open rear

cover E and remove any material in the area. Close

rear cover E and start run.

REMOVE ALL

This is due to a poor feed from manual feeder M.

FROM M & D

Check that there’s no material in manual feeder M. If

there is, remove it. Also open front cover D and remove

any material inside. Close front cover D, reload and

start

run.

REMOVE SHEET

A sheet has failed to feed from sheet feeder A1.

FROM A1

Remove paper from A1, then reload and start run.

REPLACE

Check that sheet feeder A1 is pushed fully into position.

FDR A1 TRAY

SHEETS

Envelopes have been selected but no sheet feeder was

REQUIRED

selected. The indicators for sheet feeder A1 and

envelopes will be red. Press the sheet feeder selection

button until the required feeder is selected.

SYSTEM ERROR

This is an unrecoverable system error. Please call

CALL SERVICE

Pitney Bowes for assistance (see page 41).

Summary of Contents for OFFICERIGHT DI200


















































Search results

Summary of Contents for OFFICERIGHT DI200

Reviews:

Related manuals for OFFICERIGHT DI200

Brands by name

Popular brands

Pitney Bowes OFFICERIGHT DI200, Operator'S Manual

Search results

Summary of Contents for OFFICERIGHT DI200

Reviews:

Related manuals for OFFICERIGHT DI200

Brands by name

Popular brands