background image

12

 Offi ceRight™ DI200 Operator Guide (SV41289-OG Rev. C)

 

Sheet Feeder A1 is common to all models and is located immediately 
below the Manual Feeder M. Sheet Feeder A2 is an option on all 
models. It allows the machine to insert a second folded sheet into an 
envelope. 

Both feeders are used for sheets that require folding before inserting. 
Load both feeders in exactly the same way.

Always fan (aerate) sheets before 
you load them. This prevents them 
from sticking together.

Then tap the stack of sheets onto 
a fi rm surface to align the edges.

Place the sheets into Sheet 
Feeder A1 or A2 as required.

IMPORTANT:

  

Always load sheets 
into these feeders 
face down and bot-

tom edge fi rst. The 
bottom edge of the 
sheet is furthest 
into the machine.

If you’re using both Sheet Feeders 
A1

 and

 

A2 at the same time, you 

must load the document printed 
with the address into 

Sheet Feed-

er A2

. If you load the address-

bearing document into Sheet 
Feeder A1, 

the address won’t be 

visible in the envelope window.

Slide the back stop in until it just 
touches the paper stack.

Loading

Loading the   Sheet Feeders (Feeders A1 and A2)

Summary of Contents for OFFICERIGHT DI200


















































Reviews: