Pitney Bowes OFFICERIGHT DI200 Operator'S Manual Download Page 36

Page: 36 / 49

Offi ceRight™ DI200 Operator Guide (SV41289-OG Rev. C)

Reference

Message

Meaning and Action

CHECK SHEET Sheet feeder A2 out of paper, failed to feed, or a jam that
FEEDER A2

was no cleared successfully from this area. Remove the

paper in sheet feeder A2, reload and start run.

CHECK SHEET

The machine has detected a material jam between

FEEDER A2

sheet feeder A2 and the collation area. Open the front

LIFT COVER D

cover D and remove all material inside. Close front

REMOVE ALL

cover D. Remove material from sheet feeder A2. Reload

and start run.

CLEAR FEEDER

This is due to the Manual Feeder M being blocked prior

to powering the machine up or starting it up. Check that

there’s no material in the feeder. If there is, remove it

and

restart.

CLEAR

This could be due either to a previous jam not being

STACKER AREA

cleared correctly in the stacker area or there is a jam

in the stacker area. Check that stacker area is clear.

Remove any material and resume run.

DOUBLE FEED

The machine has detected a double feed from sheet

CHECK FDR A1

feeder A1. Remove the paper in sheet feeder A1,

reload and start run.

DOUBLE FEED

The machine has detected a double feed from sheet

CHECK FDR A2

feeder A2. Remove the paper in sheet feeder A2,

reload and start run.

FOLD ONLY

Fold only has been selected but no sheets, either

REQUIRES

from feeder A1 or A2 (if applicable), have been

SHEETS

selected. In this state the indicators for sheet feeder A1

will be red, not green. Press the sheet feeder selection

button until the required feeder is selected.

Summary of Contents for OFFICERIGHT DI200


















































Search results

Summary of Contents for OFFICERIGHT DI200

Reviews:

Related manuals for OFFICERIGHT DI200

Brands by name

Popular brands

Pitney Bowes OFFICERIGHT DI200, Operator'S Manual

Search results

Summary of Contents for OFFICERIGHT DI200

Reviews:

Related manuals for OFFICERIGHT DI200

Brands by name

Popular brands