manualshive.com logo in svg

Pitney Bowes DM500, Operator'S Manual, Page: 42 / 200

Share
Download
Pitney Bowes DM500 Operator'S Manual Download Page 42

4-6

SV60890 Rev. G

4 • Running Mail

 Preparing 
Your Mail

If you intend to run pieces of mail through your system, read 

About Run-

ning Mail

 below. If you are going to print postage tapes, read 

About Print-

ing Postage Tapes

 on the following page.

Then, proceed to instructions for selecting the mode and running the job.

2

3. Adjust 

the 

 

 side guide so it is 

close to, but not touching, the 
bottom edge of the envelope 
stack. 

 

Be sure and leave a slight clear-
ance (about 1/16”) between the 
side guide and envelopes. 

 

Slide the stack all the way for-
ward until it is just inside the 
machine.

Side Guide

Refer to 

Specifications, Mailing Materials

 in 

Appendix C

 in this guide to 

make sure your mail is compatible with your mailing system.

1.  Sort mail by envelope size and, if you are using the accounting feature, 

sort by account. 

2.  Place the stack of mail on the feed deck with the  envelopes slanted 

slightly to the left (shingled) as shown in the picture below. Place the 
envelopes with the flaps down and against the rear wall.

NOTE 1:

 If you are using pre sealed envelopes, make sure you press the  Seal 

key on the IntelliLink® Control Center and select 

Sealer off

 or the envelopes 

will jam.

NOTE 2

: If you are running pieces of mail that are each 5/8” thick, you must run 

them one piece at a time. Do not stack them on the feed deck and attempt to 
feed them automatically - they will jam. 

About 
Running Mail

Summary of Contents for DM500









































































































































































































Reviews:

No comments