manualshive.com logo in svg

Pitney Bowes DM500, Operator'S Manual, Page: 183 / 200

Share
Download
Pitney Bowes DM500 Operator'S Manual Download Page 183

SV60890 Rev. G  

B-3

DM500™ and DM550™ Digital Mailing System Operating Guide

Basic Operations

Place a check mark in the 

Done 

box when you complete the topic.

How to do the following:

Refer to Chapter and Section

Page

Done

Move around, select and 
enter information in the main 
screen.

Chapter 4, Navigating Hints

4-2

Determine the best way to 
run mail on your DM Series™ 
system.

Chapter 4, Determining the Correct 
Postage Mode

4-4

Select the way you are going 
to run mail on your system.

Chapter 4, Selecting the Postage 
Mode and Running Mail

4-8

Get your mail ready to run on 
your system.

Chapter 4, Preparing Your Mail

4-6

Pick a class, carrier and/or 
special service for your mail. 

Chapter 4, Selecting a Class, Car-
rier or Special Service

4-15

Choose an account if you 
are using accounting on your 
system. 

Chapter 4, Selecting or 
Deselecting an Account

4-14

Add postage to your mail af-
ter you have already printed 
it.

Chapter 4, Adding Postage or 
Changing the Date

4-26

Change the date on your 
mail after you have already 
printed it.

Chapter 4, Adding Postage or 
Changing the Date

4-27

Connect your IntelliLink® 
Control Center (which con-
tains your postage meter) to 
an analog phone line for add-
ing postage and downloading 
updates. 

Chapter 6, Connecting Your Post-
age Meter to an Analog Phone 
Line

6-4

See how much money you 
have in your postage meter.

Chapter 6, Checking Available 
Funds in Your Postage meter

6-6

See how much money is in 
your Pitney Bowes account.

Chapter 6, Checking Your 
Postage By Phone® Meter 
Payment System Account Balance

6-7

Add postage to your postage 
meter. 

Chapter 6, Adding Postage

6-8

Print a report on an envelope 
or on a tape

Chapter 8, Printing a Report

8-2

Order replacement supplies 
for your DM Series™ Digital 
Mailing System.

Chapter 11, Ordering Supplies

11-2

Summary of Contents for DM500









































































































































































































Reviews:

No comments