Pitney Bowes DM500 Operator'S Manual Download Page 146

Page: 146 / 200

9-14

SV60890 Rev. G

9 • Maintaining and Updating

Cleaning the
Printer Nozzle

You can clean the printer nozzle at any time by following these steps:

1. From the IntelliLink® Control Center, press the

Menu

key.

2. Select

Maintenance

3. Select

Clean Printer Nozzle

. The “Cleaning Print Nozzle” screen dis-

plays until the cleaning operation completes.

4. Once the cleaning operation completes, the “Print Test Pattern” screen

appears.

5. Print a test pattern as described above in Printing a Test Pattern to

verify that you can print a clean and clear meter stamp.

6. Repeat this operation at least one more time.

8. Once the cleaning operation completes, the “Print Test Pattern” screen

appears again.

9. Repeat steps 5 and 6 again. If the print pattern still has broken or miss-

ing lines, you may need to replace the ink cartridge (see

Replacing the

Ink Cartridge

) or printhead (see

Changing the Printhead

If the test pattern is ok, go to step 10.

10. Press the left arrow key to return to the postage screen.

Printing a Test
Pattern

continued

Summary of Contents for DM500









































































































































































































Search results

Summary of Contents for DM500

Reviews:

Related manuals for DM500

Brands by name

Popular brands

Pitney Bowes DM500, Operator'S Manual

Search results

Summary of Contents for DM500

Reviews:

Related manuals for DM500

Brands by name

Popular brands