manualshive.com logo in svg

Pitney Bowes DM500, Operator'S Manual, Page: 154 / 200

Share
Download
Pitney Bowes DM500 Operator'S Manual Download Page 154

9-22

SV60890 Rev. G

9 • Maintaining and Updating

 Changing the 
Wiper Blade 
Assembly

 When you change the printhead, you must also replace the wiper blade 
assembly.

Instructions for replacing the wiper blade assembly are included with each 
replacement and are repeated here for your convenience. 

1.  From the IntelliLink® Control Center, press the 

Menu 

key.

2. Select 

Maintenance

.

3. Select 

Replace Wiper Blade Assembly

.

 

The “Preparing Wiper Blade” screen appears. During this time, the 
system moves the printhead assembly back so that you can access 
the wiper blade assembly.

4.  The “Replace Wiper Blade Assembly” screen appears instructing you 

to remove the wiper blade assembly from the package. 

5.  Lift the main cover and lo-

cate the wiper blade assem-
bly. 

6.  Push the wiper blade tab 

toward the back of the ma-
chine. This causes the wiper 
blade to slide to the left.

7.  Lift the wiper blade up and 

out of the assembly and dis-
card.

8.  Place the new wiper blade 

in the assembly with the two 
white prongs facing to the 
right. Slide it to the right until 
it snaps into place. 

Wiper Blade Tab

Wiper Blade 
Assembly

9.  Close the main cover; the “Initializing Wiper Blade” screen appears. 

10. Once the initializing is complete, the “Print Test Pattern” screen ap-

pears and prompts you to “Press Tape or print an envelope”.

 

You must perform the print test at this time. Follow the prompts, or re-
fer to 

Printing a Test Pattern

 in this chapter for more information. 

Summary of Contents for DM500









































































































































































































Reviews:

No comments