The System Setup menu
09
35
En
Subwoofer setting
This option only appears if you have connected a
subwoofer. Note that some subwoofer settings are not
available depending on other speaker settings.
Specifies the behavior of the subwoofer:
•
SUBWF 200
– Most of the bass frequencies are
played through the subwoofer
•
SUBWF 150
– Mid setting
•
SUBWF 100
– Only the very lowest bass frequencies
are played through the subwoofer
•
SUBWF –––
– No sound from the subwoofer
•
SUBWF PLS
– For extra bass power
Note
• The
SUBWF PLS
setting is only available when the
front speakers are set to
FRONT L
.
• When all speakers are set to
L
, you cannot select the
SUBWF 200
, or
SUBWF 150
settings.
• If you set the front speakers to
FRONT S
, you cannot
select the
SUBWF –––
setting.
• Depending on the source and other receiver settings,
you may not always hear sound from the subwoofer.
LFE attenuator setting
Dolby Digital and DTS audio sources include ultra-low
bass tones. Set the LFE attenuator as needed to prevent
the ultra-low bass from distorting the sound.
•
LFEATT 0
– The LFE channel is played with no
attenuation
•
LFEATT10
– LFE channel is attenuated by 10 dB
•
LFE OFF
– LFE channel is not played
Front-left speaker distance setting
Specifies the distance from your listening position to the
front-left speaker:
•
L 0.1 m.
–
L 9.0 m.
– Distance can be set in
increments of 0.1 m. The default is 2.0 m.
Center speaker distance setting
Specifies the distance from your listening position to the
center speaker:
•
C 0.1 m.
–
C 9.0 m.
– Distance can be set in
increments of 0.1 m. The default is 2.0 m.
Front-right speaker distance setting
Specifies the distance from your listening position to the
front-right speaker:
•
R 0.1 m.
–
R 9.0 m.
– Distance can be set in
increments of 0.1 m. The default is 2.0 m.
Right-surround speaker distance setting
Specifies the distance from your listening position to the
surround-right speaker:
•
RS 0.1 m.
–
RS 9.0 m.
– Distance can be set in
increments of 0.1 m. The default is 2.0 m.
Surround-back speaker distance setting
Specifies the distance from your listening position to the
surround-back speaker:
•
SB 0.1 m.
–
SB 9.0 m.
– Distance can be set in
increments of 0.1 m. The default is 2.0 m.
Left-surround speaker distance setting
Specifies the distance from your listening position to the
left-surround speaker:
•
LS 0.1 m.
–
LS 9.0 m.
– Distance can be set in
increments of 0.1 m. The default is 2.0 m.
Subwoofer distance setting
Specifies the distance from your listening position to the
subwoofer:
•
SW 0.1 m.
–
SW 9.0 m.
– Distance can be set in
increments of 0.1 m. The default is 2.0 m.
Dynamic Range Control
Specifies the amount of dynamic range adjustment to
Dolby Digital or DTS soundtracks:
•
DRC OFF
– No dynamic range adjustment (use when
listening at higher volume)
•
DRC MAX
– Dynamic range is reduced (loud sounds
are reduced in volume while quieter sounds are
increased)
•
DRC MID
– Mid setting
Note
• This setting works only with Dolby Digital or DTS
soundtracks. For other sources you can create a
similar effect using the Midnight mode (see
Using
the Sound Modes
on page 28).
vsx-c501(FL).book 35 ページ ２００３年６月１３日 金曜日 午後１２時４６分
