Pioneer VSX-934 Instruction Manual Download Page 39

Page: 39 / 153

≫

≫

≫

≫

≫

≫

To ARC TV

If the TV supports the ARC (Audio Return Channel) function (*), use only the

HDMI cable to connect with the TV. Use the ARC-compatible HDMI IN jack of the

TV for connection.

•

Another TV or projector can be connected to the HDMI OUT SUB jack. Switch

between MAIN and SUB using the HDMI MAIN/SUB button (

p16

) on the

remote controller or "AV Adjust" (

p129

). Note that this jack is not ARC-

compatible.

•

If devices with different resolutions are connected to HDMI OUT MAIN jack

and SUB jack, images are output with the lower resolution.

Setup

•

Settings are required to use the ARC function. Select "Yes" for "5. ARC Setup"

in Initial Setup (

p132

). If "No, Skip" is selected, settings are required in the

System Setup menu after Initial Setup is completed. Press the button on

the remote controller to display the Home screen, and select "System Setup" -

"Hardware" - "HDMI" (

p113

) to make the following settings.

–

Set "HDMI CEC" to "On".

– Set "Audio Return Channel" to "Auto".

• For detailed settings for TV connection, CEC function and audio output, refer

to the instruction manual of the TV.

(*) ARC function: This function transmits the audio signals of the TV via an

HDMI cable, and plays the audio of the TV on this unit. Connection to an ARC-

compatible TV is complete with one HDMI cable. To check if the TV supports the

ARC function, refer to the instruction manual of the TV, etc.

HDMI cable

IN(ARC)

Summary of Contents for VSX-934


























































































































































Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands

Pioneer VSX-934, Instruction Manual

Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands