Pioneer VSX-934 Instruction Manual Download Page 132

Page: 132 / 153

132

≫

≫

≫

≫

≫

≫

Initial Setup with Auto Start-up Wizard

Operations

When you turn the unit on for the first time after purchase, the Initial Setup screen

is automatically displayed on the TV to allow you to make settings required for

startup using simple operations following on-screen guidance.

Switch the input of the TV to the input connected to the unit.

2. Put batteries into the remote controller of this unit.

3. Press on the remote controller to turn the unit on.

4. When the language selection screen is displayed on TV, select the language

with the cursors

/ and press ENTER.

•

Select the item with the cursors of the remote controller, and press ENTER to

confirm your selection. To return to the previous screen, press

/ / /

ENTER

+Fav

CLEAR

Inputs

HDMI 1

HDMI 2

HDMI 3

INPUT

TV’s REMOTE

Summary of Contents for VSX-934


























































































































































Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands

Pioneer VSX-934, Instruction Manual

Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands