Pioneer VSX-934 Instruction Manual Download Page 100

Page: 100 / 153

100

Setup

≫

≫

≫

≫

≫

≫

System Setup

Menu list

You can configure advanced settings to have a more enjoyable experience with this unit. For operation details, refer to "Menu operations" (

p102

Input/Output

Assign

TV Out / OSD

Make settings for TV output and On-Screen Displays (OSD) that appear on the TV.

p103

HDMI Input

Change input assignment between the input selectors and HDMI IN jacks.

p104

Digital Audio Input

Change input assignment between the input selectors and DIGITAL IN COAXIAL/OPTICAL jacks.

p104

Analog Audio Input

Change input assignment between the input selectors and AUDIO IN jacks.

p105

Input Skip

You can skip inputs to which nothing is connected when selecting them with the INPUT

SELECTOR dial on the main unit or with the input selectors on the remote controller.

p105

PERSONAL PRESET

Information

Confirm the registered contents of PERSONAL PRESET.

p105

Speaker

Configuration

Change the settings of connection environment of the speakers.

p106

Crossover

Change the settings of crossover frequencies.

p107

Distance

Set the distance from each speaker to the listening position.

p108

Channel Level

Adjust the volume level of each speaker.

p109

Dolby Enabled Speaker

Change the settings of Dolby Enabled Speakers.

p110

Speaker Virtualizer

The Speaker Virtualizer function can be switched between On and Off.

p110

Audio Adjust

Dual Mono/Mono

Change the settings of multiplex audio playback.

p110

Dolby

Change the setting of when Dolby signals are input.

p110

Volume

Change the Volume settings.

p111

Source

Input Volume Absorber

Adjust the volume level when there are differences in volume level among multiple devices

connected to this unit.

p111

Name Edit

Set an easy name for each input.

p112

Audio Select

Select the priority for input selection when multiple audio sources are connected to one input

selector.

p112

Summary of Contents for VSX-934


























































































































































Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands

Pioneer VSX-934, Instruction Manual

Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands