Pioneer VSX-934 Instruction Manual Download Page 107

Page: 107 / 153

107

≫

≫

≫

≫

≫

≫

Setting Item

Default Value

Setting Details

Bi-Amp

Set whether the front speakers are bi-amp

connected.

"No": When front speakers are not bi-amp

connected

"Yes": When front speakers are bi-amp connected

•

This setting is fixed to "No" if "Zone Speaker" is

set to "Zone 2".

•

This setting cannot be selected when surround

back speakers or height speakers are installed.

Speaker

Impedance

6 ohms or above Set the impedance (Ω) of the connected speakers.

"4ohms": When any of the connected speakers

have 4 Ω or more to less than 6 Ω impedance

"6 ohms or above": When the connected speakers

all have 6 Ω or more impedance

• For impedance, check the indications on the

back of the speakers or their instruction manual.

Crossover

Change the settings of crossover frequencies.

Setting Item

Default Value

Setting Details

Front

Small

Set the low range capabilities for each channel by

setting either small or large.

"Small": For small speakers whose low range

capabilities may be limited

"Large": For full-range speakers with sufficient low

range capabilities

•

If "Configuration" - "Subwoofer" is set to "No",

"Front" will be fixed to "Large" and the low

pitched range of the other channels will be output

from the front speakers. Refer to the instruction

manual of your speakers to make the setting.

Center

Small

Set the low range capabilities for each channel by

setting either small or large.

"Small": For small speakers whose low range

capabilities may be limited

"Large": For full-range speakers with sufficient low

range capabilities

• When "Front" is set to "Small", this is set to

"Small".

• If an item cannot be selected even though

connection is correct, check that the settings in

"Configuration" - "Speaker Channels" matches

the number of connected channels.

Height

Small

Set the low range capabilities for each channel by

setting either small or large.

"Small": For small speakers whose low range

capabilities may be limited

"Large": For full-range speakers with sufficient low

range capabilities

• When "Front" is set to "Small", this is set to

"Small".

• If an item cannot be selected even though

connection is correct, check that the settings in

"Configuration" - "Speaker Channels" matches

the number of connected channels.

Summary of Contents for VSX-934


























































































































































Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands

Pioneer VSX-934, Instruction Manual

Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands