background image

Controls & Connections (Side Panel)




 PTT (Push To Talk) Switch ..................................................

 21

  •  Press this switch to transmit, and release it (to receive) after your trans-

mission is completed.

  •  In the Set mode, press the PTT switch to save the new setting and return 

to normal operation.

‚

 MONI/T.CALL Key (Function is selectable from Set mode)

 .....................................................................................................

 28

 

USA/Asian Version:

  Press this switch to open the squelch, and listen for very weak signals 

near the background noise level.

 

European Version:

  Pressing this switch activates the T-CALL (1750 Hz) for repeater access.

ƒ

 F key .....................................................................................

 22

  Press and hold this key to enter the Set Mode.

„

 SP Jack

  This three-conductor miniature jack provides connection for an external 

speaker.

…

 MIC Jack

  This three-conductor miniature jack provides connections for microphone 

audio, earphone audio, PTT, and ground.

11

FT-25R/FT-25E Operating Manual

Application for FCC / IC 

FCC ID: K6620663X20, IC: 511B-20663X20

Summary of Contents for 20663X20





















Reviews: