Pioneer VSX-934 Instruction Manual Download Page 145

Page: 145 / 153

145

≫

≫

≫

≫

≫

≫

ZONE B function

❏

Cannot output audio to ZONE B

•

To output audio to ZONE B, set the audio output destination to "ZONE A+B" or "ZONE B".

(

p77

)

Multi-zone function

❏

Cannot ZONE-output the audio of externally connected AV components

•

To output audio from an externally connected AV component to ZONE 2, connect it to any of HDMI IN1 to IN3 jacks. If the AV component is not

equipped with an HDMI jack, use a digital coaxial cable, digital optical cable or analog audio cable. Also, the audio from externally connected AV

components can be output to ZONE 2 only when the audio is analog or 2ch PCM signal. When the AV component is connected to this unit with an

HDMI cable, digital coaxial cable or digital optical cable, change the audio output of the AV component to the PCM output.

•

When video and audio via HDMI input are output to ZONE 2, set "Input/Output Assign" - "TV Out / OSD" - "Zone 2 HDMI" (

p103

) to "Use" on

the System Setup menu.

❏

Others

•

If the audio signal is from the NET or USB input selector, zone output is not possible for DSD audio signals.

Remote Controller

•

Make sure that the batteries are inserted with the correct polarity.

•

Insert new batteries. Do not mix different types of batteries, or old and new batteries.

•

Make sure that the sensor of the main unit is not subjected to direct sunlight or inverter-type fluorescent lights. Relocate it if necessary.

•

If the main unit is installed in a rack or cabinet with colored-glass doors, or if the doors are closed, the remote controller may not work normally.

Display

❏

The display does not light up

•

When the Dimmer function is working, the display may go dim or turn off. Press the DIMMER button, and change the brightness level of the

display.

(

p11

)

Others

❏

Strange noise can be heard from the unit

•

If you have connected another device to the same outlet as this unit, strange noise may occur under the influence of the device. If the symptom is

remedied by removing the power plug of the other device from the outlet, use different outlets for this unit and the device.

Summary of Contents for VSX-934


























































































































































Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands

Pioneer VSX-934, Instruction Manual

Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands