Pioneer VSX-934 Instruction Manual Download Page 11

Page: 11 / 153

≫

≫

≫

≫

≫

≫

INPUT SELECTOR dial: Switch the input to be played.

DIMMER button: You can switch the display off or adjust the brightness of the

display in three steps.

FL OFF indicator: This lights when you have pressed DIMMER repeatedly to

turn the display off.

ZONE 2-ON/OFF button: Switches the multi-zone function on/off. (

p76

)

5. ZONE 2-CONTROL button: Controls the multi-zone function. (

p76

)

6. HOME MENU button: Displays the Home. (

p102, 120, 125

)

Display (

p12

)

Cursor buttons ( / / / )

and ENTER button: Select the item with the

cursors and press ENTER to confirm. Use them to tune to stations when using

TUNER. (

p70

)

NETWORK indicator: This lights when "NET" is selected with the input

selector and the unit is connected to the network. Lights up when any of the

following functions is working or enabled in standby state of this unit. When

this indicator is lighting, the power consumption in standby state increases,

however, the increase in power consumption is minimized by entering the

HYBRID STANDBY mode where only the essential circuits operate. It does not

light when ZONE 2 is on, however.

–

HDMI CEC (

p113

)

–

HDMI Standby Through (

p114

)

–

USB Power Out at Standby (

p115

)

–

Network Standby (

p115

)

–

Bluetooth Wakeup (

p116

)

10.

MCACC indicator: This lights when you have enabled the speaker calibration

made with MCACC. (

p121, 133

)

11. Remote control sensor: Receives signals from the remote controller.

•

The signal range of the remote controller is within about 16´/5 m, at an

angle of 20° on the perpendicular axis and 30° to either side.

12. RETURN button: Returns the display to the previous state.

13. MASTER VOLUME

14.

STANDBY/ON button

15. PHONES jack: Headphones with a standard plug (ø1/4"/6.3 mm) are

connected.

16.

SETUP MIC jack: The supplied speaker setup microphone is connected.

(

p121, 133

)

17. TUNER button: Switches the input to be played to "TUNER". Also, pressing

this button repeatedly switches the input between "AM" and "FM".

18.

PERSONAL PRESET 1/2/3 buttons: Registers the current setting conditions

such as input selector, listening mode, etc. or call the registered settings.

(

p78

)

19.

Listening mode button: Switches the listening mode. (

p83

)

20.

USB port: A USB storage device is connected so that music files stored in it

can be played. (

p57

) You can also supply power (5 V/500 mA) to USB

devices with a USB cable.

21. AUX INPUT jack: Connect a mobile music player, etc. using a stereo mini plug

cable (ø1/8″/3.5 mm).

Summary of Contents for VSX-934


























































































































































Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands

Pioneer VSX-934, Instruction Manual

Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands