Pioneer VSX-934 Instruction Manual Download Page 116

Page: 116 / 153

116

≫

≫

≫

≫

≫

≫

Setting Item

Default Value

Setting Details

Bluetooth Wakeup Off

This function wakes up the unit on standby by

connecting a BLUETOOTH-enabled device.

"On": When this function is used

"Off": When this function is not used

•

When this function is set to "On", the power

consumption in standby state increases,

however, the increase in power consumption

is minimized by automatically entering the

HYBRID STANDBY mode where only the

essential circuits operate.

•

This setting is fixed to "Off" if "Network/

Bluetooth" - "Bluetooth" - "Auto Input Change" is

set to "Off".

•

Wait for a while if "Network Standby" and "Bluetooth Wakeup" cannot be selected. It can

be selected when the network function is activated.

Works with SONOS

Change the settings to connect with the Sonos Connect.

Setting Item

Default Value

Setting Details

Input Selector

Off

Select the input selector to which the Sonos

Connect is connected.

•

Selecting "Off" disables the interlock function

with Sonos.

Connected Device -

Displays the Sonos Connect connected to the

same network as the network of this unit. Press

the ENTER button to select the connected Sonos

Connect.

•

Products (e.g. Play:3 unequipped with an output

terminal) other than the Sonos Connect are also

displayed in the device list and selectable. In that

case, when playback on the Sonos side starts,

the input is switched, however, audio is not

output. Select the room name of the connected

Sonos Connect.

• Up to 32 devices can be displayed on the Sonos

product list screen. If you cannot find the Sonos

Connect to be interlocked, return to the previous

screen, turn off the product you want to interlock,

and try again.

• To use this function, set "Input Selector"

beforehand.

Output Zone

Main

Select the zone where you want to listen to the

music.

"Main": Outputs audio only to the main room

(where this unit is located).

"Zone 2": Outputs audio only to the separate room

(ZONE 2).

"Main/Zone 2": Outputs audio to both the main

room and separate room.

• To use this function, set "Input Selector"

beforehand.

Summary of Contents for VSX-934


























































































































































Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands

Pioneer VSX-934, Instruction Manual

Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands