Pioneer VSX-934 Instruction Manual Download Page 12

Page: 12 / 153

≫

≫

≫

≫

≫

≫

Display

This may light when performing operations with the "NET", "USB" input

selector.

Lights in the following conditions.

Z2: ZONE 2 is on.

: Connected by BLUETOOTH.

: Connected by Wi-Fi.

NET: Lights when connected to the network with the "NET" input selector. It

will blink if incorrectly connected to the network.

USB: Lights when the "USB" input selector is selected, a USB device is

connected and the USB input is selected. It will blink if the USB device is not

properly connected.

HDMI: HDMI signals are input and the HDMI input is selected.

DIGITAL: Digital signals are input and the digital input is selected.

3. Lights according to the type of input digital audio signal and the listening

mode.

Lights in the following conditions.

RDS (European, Australian and Asian models): Receiving RDS broadcasting.

TUNED: Receiving AM/FM radio.

STEREO: Receiving FM stereo.

SLEEP: Sleep timer is set. (

p115

)

AUTO STBY: Auto Standby is set. (

p115

)

Displays the audio output destination.

A: Outputs audio only to ZONE A.

B: Outputs audio only to ZONE B.

AB: Outputs audio to both ZONE A and ZONE B.

6. Lights when headphones are connected.

7. Blinks when muting is on.

Displays various information of the input signals.

Lights when adjusting the volume.

10. Speaker/Channel display: Displays the output channel that corresponds to the

selected listening mode.

6 7

9 bk

Summary of Contents for VSX-934


























































































































































Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands

Pioneer VSX-934, Instruction Manual

Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands