Pioneer VSX-934 Instruction Manual Download Page 129

Page: 129 / 153

129

≫

≫

≫

≫

≫

≫

AV Adjust

Menu operations

You can quickly adjust the settings you frequently use, such as tone adjustments,

etc.

You can make the settings on the TV screen while playing something. Press

on the remote controller to display the AV Adjust menu. Note that there is no

display on the TV screen when the input selector is "AUX", "CD", "TV", "PHONO",

"FM", or "AM", so follow the main unit’s display while doing the operations.

AV Adjust
Tone
Level
MCACC
Other

Bass
Dialog
Treble

BD/DVD

Select the item with the cursor

/ buttons of the remote controller and press

ENTER to confirm your selection.

Use the cursors to change the settings.

• To return to the previous screen, press .

• To exit the settings, press .

Tone

Bass:

Enhance or moderate the bass range of the speaker.

Dialog:

Emphasizes movie lines and music vocals to listen to them more easily.

Treble:

Enhance or moderate the treble range of the speaker.

• It cannot be set if the listening mode is Direct or Pure Direct.

• Depending on the input source or listening mode setting, selection is not

possible, or the desired effect may not be achieved.

Level

Center:

Adjust the speaker level of the center speaker while listening to the

sound.

Summary of Contents for VSX-934


























































































































































Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands

Pioneer VSX-934, Instruction Manual

Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands