manualshive.com logo in svg

Philips LPC214 Series, User Manual

The Philips LPC214 Series is a cutting-edge product designed to meet your needs. With our comprehensive and user-friendly User Manual, you can easily navigate through all the features and functionalities. Download this manual for free from our website, ensuring a hassle-free experience.

Share
Download
background image

Philips Semiconductors

UM10139

Volume 1

Chapter 25: Supplementary information

 

© Koninklijke Philips Electronics N.V. 2005. All rights reserved.

User manual

Rev. 01 — 15 August 2005 

333

continued >>

 

bit description . . . . . . . . . . . . . . . . . . . . . . . . .101

Table 105:UART0 interrupt handling . . . . . . . . . . . . . . . .102
Table 106:UART0 FIFO Control Register (U0FCR - address 

0xE000 C008) bit description . . . . . . . . . . . . .103

Table 107:UART0 Line Control Register (U0LCR - address 

0xE000 C00C) bit description . . . . . . . . . . . . .103

Table 108:UART0 Line Status Register (U0LSR - address 

0xE000 C014, read only) bit description. . . . .104

Table 109:UART0 Scratch pad register (U0SCR - address 

0xE000 C01C) bit description . . . . . . . . . . . . .105

Table 110:Auto-baud Control Register (U0ACR - 

0xE000 C020) bit description . . . . . . . . . . . . .106

Table 111:UART0 Transmit Enable Register (U0TER - 

address 0xE000 C030) bit description . . . . . .107

Table 112:UART1 pin description  . . . . . . . . . . . . . . . . . .112
Table 113:UART1 register map   . . . . . . . . . . . . . . . . . . .114
Table 114:UART1 Receiver Buffer Register (U1RBR - 

address 0xE001 0000, when DLAB = 0 Read 
Only) bit description  . . . . . . . . . . . . . . . . . . . .115

Table 115:UART1 Transmitter Holding Register (U1THR - 

address 0xE001 0000, when DLAB = 0 Write 
Only) bit description . . . . . . . . . . . . . . . . . . . .115

Table 116:UART1 Divisor Latch LSB register (U1DLL - 

address 0xE001 0000, when DLAB = 1) bit 
description  . . . . . . . . . . . . . . . . . . . . . . . . . . .116

Table 117:UART1 Divisor Latch MSB register (U1DLM - 

address 0xE001 0004, when DLAB = 1) bit 
description  . . . . . . . . . . . . . . . . . . . . . . . . . . .116

Table 118:UART1 Fractional Divider Register (U1FDR - 

address 0xE001 0028) bit description  . . . . . .116

Table 119:Baudrates available when using 20 MHz 

peripheral clock (PCLK = 20 MHz) . . . . . . . . .117

Table 120:UART1 Interrupt Enable Register (U1IER - 

address 0xE001 0004, when DLAB = 0) bit 
description  . . . . . . . . . . . . . . . . . . . . . . . . . . .118

Table 121:UART1 Interrupt Identification Register 

 

(U1IIR - address 0xE001 0008, read only) 

 

bit description . . . . . . . . . . . . . . . . . . . . . . . . .119

Table 122:UART1 interrupt handling . . . . . . . . . . . . . . . .121
Table 123:UART1 FIFO Control Register (U1FCR - address 

0xE001 0008) bit description  . . . . . . . . . . . . .122

Table 124:UART1 Line Control Register (U1LCR - address 

0xE001 000C) bit description . . . . . . . . . . . . .122

Table 125:UART1 Modem Control Register (U1MCR - 

address 0xE001 0010), LPC2144/6/8 only bit 
description  . . . . . . . . . . . . . . . . . . . . . . . . . . .123

Table 126:Modem status interrupt generation . . . . . . . . .125
Table 127:UART1 Line Status Register (U1LSR - address 

0xE001 0014, read only) bit description . . . . .125

Table 128:UART1 Modem Status Register (U1MSR - 

address 0xE001 0018), LPC2144/6/8 only bit 

description . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Table 129:UART1 Scratch pad register (U1SCR - address 

0xE001 0014) bit description . . . . . . . . . . . . . 127

Table 130:Auto-baud Control Register (U1ACR - 

0xE001 0020) bit description . . . . . . . . . . . . . 128

Table 131:UART1 Transmit Enable Register (U1TER - 

address 0xE001 0030) bit description . . . . . . 131

Table 132:I

2

C Pin Description. . . . . . . . . . . . . . . . . . . . . 134

Table 133:I2C0CONSET and I2C1CONSET used to 

configure Master mode  . . . . . . . . . . . . . . . . . 135

Table 134:I2C0CONSET and I2C1CONSET used to 

configure Slave mode  . . . . . . . . . . . . . . . . . . 136

Table 135:I

2

C register map . . . . . . . . . . . . . . . . . . . . . . . 142

Table 136:I

2

C Control Set register (I2CONSET: I2C0, 

I2C0CONSET - address 0xE001 C000 and I2C1, 
I2C1CONSET - address 0xE005 C000) bit 
description . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

Table 137:I

2

C Control Set register (I2CONCLR: I2C0, 

I2C0CONCLR - address 0xE001 C018 and I2C1, 
I2C1CONCLR - address 0xE005 C018) bit 
description . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

Table 138:I

2

C Status register (I2STAT: I2C0, I2C0STAT - 

address 0xE001 C004 and I2C1, I2C1STAT - 
address 0xE005 C004) bit description . . . . . . 145

Table 139:I

2

C Data register (I2DAT: I2C0, I2C0DAT - address 

0xE001 C008 and I2C1, I2C1DAT - address 
0xE005 C008) bit description. . . . . . . . . . . . . 145

Table 140:I

2

C Slave Address register (I2ADR: 

 

I2C0, I2C0ADR - address 0xE001 C00C and 
I2C1, I2C1ADR - address 0xE005 C00C) 

 

bit description. . . . . . . . . . . . . . . . . . . . . . . . . 146

Table 141:I

2

C SCL High Duty Cycle register (I2SCLH: I2C0, 

I2C0SCLH - address 0xE001 C010 and I2C1, 
I2C1SCLH - address 0xE005 C010) bit 
description . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

Table 142:I

2

C SCL Low Duty Cycle register (I2SCLL: 

 

I2C0, I2C0SCLL - address 0xE001 C014 and 
I2C1, I2C1SCLL - address 0xE005 C014) 

 

bit description. . . . . . . . . . . . . . . . . . . . . . . . . 146

Table 143:Example I

2

C clock rates . . . . . . . . . . . . . . . . . 147

Table 144:Abbreviations used to describe an I

2

C 

 

operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

Table 145:I2CONSET used to initialize Master Transmitter 

mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

Table 146:I2C0ADR and I2C1ADR usage in Slave Receiver 

mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

Table  147:I2C0CONSET and I2C1CONSET used to initialize 

Slave Receiver mode . . . . . . . . . . . . . . . . . . . 149

Table 148:Master Transmitter mode . . . . . . . . . . . . . . . . 154
Table 149:Master Receiver mode . . . . . . . . . . . . . . . . . . 155
Table 150:Slave Receiver mode . . . . . . . . . . . . . . . . . . . 156

Summary of Contents for LPC214 Series





























































































































































































































































































































































Reviews:

No comments

Related manuals for LPC214 Series

Fairchild 63 Installation, Operation And Maintenance Instructions preview
63
Brand: Fairchild Pages: 2
Hach SC1500 User Manual preview
SC1500
Brand: Hach Pages: 86
Caen V793 Technical Information Manual preview
V793
Brand: Caen Pages: 20
ECKELMANN VS 3010 BS Operating Instruction preview
VS 3010 BS
Brand: ECKELMANN Pages: 178
H3C WX Series Registration And Activation Manual preview
WX Series
Brand: H3C Pages: 17
H3C WX Series Getting Started Manual preview
WX Series
Brand: H3C Pages: 32
KAESER KOMPRESSOREN SIGMA CONTROL 2 User Manual preview
SIGMA CONTROL 2
Brand: KAESER KOMPRESSOREN Pages: 246
LAE electronic LF28 Instructions For Installation And Use Manual preview
LF28
Brand: LAE electronic Pages: 7
LAE electronic AT1-5 Instructions For Use preview
AT1-5
Brand: LAE electronic Pages: 2
Xilinx ZC702 Getting Started Manual preview
ZC702
Brand: Xilinx Pages: 52
LMI Technologies Liquitron DP5000-01A Instruction Manual preview
Liquitron DP5000-01A
Brand: LMI Technologies Pages: 28
Watlow DIN-A-MITE C User Manual preview
DIN-A-MITE C
Brand: Watlow Pages: 20
Sutter Instrument TRIO MPC-165 Series Operation Manual preview
TRIO MPC-165 Series
Brand: Sutter Instrument Pages: 60
Vent-Axia SAC 5 Installation And Wiring Instructions preview
SAC 5
Brand: Vent-Axia Pages: 4
Eaton C22- P Series Instruction Leaflet preview
C22- P Series
Brand: Eaton Pages: 2
Rauch quantron e Operator'S Manual preview
quantron e
Brand: Rauch Pages: 85
Texas Instruments CC2530-CC2592EM Quick Start Manual preview
CC2530-CC2592EM
Brand: Texas Instruments Pages: 3
Badger Meter MDS 2000 User Manual preview
MDS 2000
Brand: Badger Meter Pages: 66

Brands by name

Popular brands

Load more brands