manualshive.com logo in svg

Philips LPC214 Series, User Manual

The Philips LPC214 Series is a cutting-edge product designed to meet your needs. With our comprehensive and user-friendly User Manual, you can easily navigate through all the features and functionalities. Download this manual for free from our website, ensuring a hassle-free experience.

Share
Download
background image

 

© Koninklijke Philips Electronics N.V. 2005. All rights reserved.

User manual

Rev. 01 — 15 August 2005 

190

Philips Semiconductors

UM10139

Volume 1

Chapter 13: SSP

 

13.4.2 SSP 

Control 

Register 1 (SSPCR1 - 0xE006 8004)

This register controls certain aspects of the operation of the SSP controller.

6

CPOL

0

Clock Out Polarity. This bit is only used in SPI mode.

SSP controller captures serial data on the first clock transition 
of the frame, that is, the transition away from the inter-frame 
state of the clock line.

0

1

SSP controller captures serial data on the second clock 
transition of the frame, that is, the transition back to the 
inter-frame state of the clock line.

7

CPHA

0

Clock Out Phase. This bit is only used in SPI mode.

SSP controller maintains the bus clock low between frames.

0

1

SSP controller maintains the bus clock high between frames.

15:8

SCR

Serial Clock Rate. The number of prescaler-output clocks per 
bit on the bus, minus one. Given that CPSDVR is the prescale 
divider, and the VPB clock PCLK clocks the prescaler, the bit 
frequency is PCLK / (CPSDVSR * [SCR+1]).

0x00

Table 163: SSP Control Register 0 (SSPCR0 - address 0xE006 8000) bit description

Bit

Symbol

Value

Description

Reset 
value

Table 164: SSP Control Register 1 (SSPCR1 - address 0xE006 8004) bit description

Bit

Symbol

Value

Description

Reset 
value

0

LBM

0

Loop Back Mode.

During normal operation.

0

1

Serial input is taken from the serial output (MOSI or MISO) 
rather than the serial input pin (MISO or MOSI 
respectively).

1

SSE

0

SSP Enable.

The SSP controller is disabled.

0

1

The SSP controller will interact with other devices on the 
serial bus. Software should write the appropriate control 
information to the other SSP registers and interrupt 
controller registers, before setting this bit.

2

MS

0

Master/Slave Mode.This bit can only be written when the 
SSE bit is 0.

The SSP controller acts as a master on the bus, driving the 
SCLK, MOSI, and SSEL lines and receiving the MISO line.

0

1

The SSP controller acts as a slave on the bus, driving 
MISO line and receiving SCLK, MOSI, and SSEL lines.

3

SOD

Slave Output Disable. This bit is relevant only in slave 
mode (MS = 1). If it is 1, this blocks this SSP controller 
from driving the transmit data line (MISO).

0

7:4

-

Reserved, user software should not write ones to reserved 
bits. The value read from a reserved bit is not defined.

NA

Summary of Contents for LPC214 Series





























































































































































































































































































































































Reviews:

No comments

Related manuals for LPC214 Series

Yardney Synergy Quick Start Manual preview
Synergy
Brand: Yardney Pages: 8
SDC E4KP ENTRYCHECK Operating Instructions Manual preview
E4KP ENTRYCHECK
Brand: SDC Pages: 6
Grosvenor Janus C4 485 Installation Manual preview
Janus C4 485
Brand: Grosvenor Pages: 5
S.E.A. Group Sundstrom SR307 Manual preview
Sundstrom SR307
Brand: S.E.A. Group Pages: 5
ICP DAS USA ISaGRAF WinCE ViewPAC User Manual preview
ISaGRAF WinCE ViewPAC
Brand: ICP DAS USA Pages: 192
J+J J4C B140 Handbook preview
J4C B140
Brand: J+J Pages: 91
CDVI Ievo User Manual preview
Ievo
Brand: CDVI Pages: 24
Kamado Joe iKAMAND User Manual preview
iKAMAND
Brand: Kamado Joe Pages: 2
Parker PAC120 Series Operation Manual preview
PAC120 Series
Brand: Parker Pages: 31
Eaton FC6 User Manual preview
FC6
Brand: Eaton Pages: 10
Go Power GP-RVC-R Quick Start Manual preview
GP-RVC-R
Brand: Go Power Pages: 2
Samson EB 31a Mounting And Operating Instructions preview
EB 31a
Brand: Samson Pages: 68
Cumberland Smart-Flex FLX-4629 Operation Instructions Manual preview
Smart-Flex FLX-4629
Brand: Cumberland Pages: 30
PXM PX268 User Manual preview
PX268
Brand: PXM Pages: 10
PRECISION DIGITAL PD6200 Instruction Manual preview
PD6200
Brand: PRECISION DIGITAL Pages: 96
IBM ServeRAID M1015 SAS/SATA Quick Install Manual preview
ServeRAID M1015 SAS/SATA
Brand: IBM Pages: 4
dixell XR30CX Installation And Operating Instructions preview
XR30CX
Brand: dixell Pages: 4
Wecon LX3V-4AD User Manual preview
LX3V-4AD
Brand: Wecon Pages: 12

Brands by name

Popular brands

Load more brands