manualshive.com logo in svg

Philips LPC214 Series, User Manual

The Philips LPC214 Series is a cutting-edge product designed to meet your needs. With our comprehensive and user-friendly User Manual, you can easily navigate through all the features and functionalities. Download this manual for free from our website, ensuring a hassle-free experience.

Share
Download
background image

9397 750 XXXXX

© Koninklijke Philips Electronics N.V. 2005. All rights reserved.

User manual

Rev. 01 — 15 August 2005 

235

Philips Semiconductors

UM10139

Volume 1

Chapter 14: USB Device Controller

 

The full DMA descriptor (4 words) will in turn be fetched from this address pointed by DDP. 
The DD will give the details of the transfer to be done. The DMA engine will load its 
hardware resources with the information fetched from the DD (start address, DMA count 
etc.).

If the ‘next_dd_valid’ is not set and the DD_retired bit is set the DMA engine will raise the 
‘NEW_DD_REQUEST’ interrupt for this endpoint. It also disables the DMA_ENABLE bit.

14.12.3 Transferring 

the 

Data

In case of OUT endpoints, the current packet will be read from the EP_RAM by the DMA 
Engine and will get transferred to the USB RAM memory locations starting from the 
address pointed by ‘dma_buffer_start_addr’. In case of IN endpoints, the data will be 
fetched from the USB RAM and will be written to the EP_RAM. The 
‘dma_buffer_start_addr’ and ‘present_dma_count’ will get updated while the transfer 
progresses.

14.12.4 Optimizing Descriptor Fetch

A DMA transfer normally involves multiple packet transfers. If a DD once fetched is 
equipped to do multiple transfers, the hardware will not fetch DD for all the succeeding 
packets. It will do the fetching only if the previous packet transferred on this channel does 
not belong to this endpoint. This is on the assumption that the current contents of the 
hardware resource and that of the descriptor to be fetched will be the same. In such a 
case DMA engine can proceed without fetching the new descriptor if it has not transferred 
enough data specified in the ‘dma_buffer_length’ field of the descriptor. To keep this 
information the hardware will have a flag set called ‘DMA_PROCEED’.

This flag will be reset after the required number of bytes specified in the 
‘dma_buffer_length’ field is transferred. It is also reset when the software writes into the 
EP DMA Disable register. This will give the software control over the reading of DD by the 
hardware. Hardware will be forced to read the DD for the next packet. Writing data 0x0 
into the EP DMA Disable register will cause only resetting of the DMA_PROCEED flag 
without disabling DMA for any endpoint.

Fig 53. Finding the DMA descriptor

USB

Device

Controller

USB RAM

DDP-EP31

DD-EP2

DD-EP31

0

1

31

UDCA Head

Register

DDP-EP2

2

Summary of Contents for LPC214 Series





























































































































































































































































































































































Reviews:

No comments

Related manuals for LPC214 Series

Danfoss VLT AutomationDrive FC 302 Installation Manual preview
VLT AutomationDrive FC 302
Brand: Danfoss Pages: 128
Eaton S701 Instruction Leaflet preview
S701
Brand: Eaton Pages: 8
S&P RMB Quick Start Manual preview
RMB
Brand: S&P Pages: 17
YASKAWA U1000 iQpump Drive Quick Start Quide preview
U1000 iQpump Drive
Brand: YASKAWA Pages: 26
YASKAWA Z1000 CIMR-ZU*A Series Quick Start Up Manual preview
Z1000 CIMR-ZU*A Series
Brand: YASKAWA Pages: 2
Eaton CDAU-01/04 Instruction Leaflet preview
CDAU-01/04
Brand: Eaton Pages: 4
Audioaccess PX-700 Manual preview
PX-700
Brand: Audioaccess Pages: 2
Watlow EZ-ZONE PM L AAAAB Series User Manual preview
EZ-ZONE PM L AAAAB Series
Brand: Watlow Pages: 30
Danfoss AMV 20 SL Operating Manual preview
AMV 20 SL
Brand: Danfoss Pages: 4
Genius BRAIN 06 24V Manual preview
BRAIN 06 24V
Brand: Genius Pages: 52
Neousys Technology Nuvo-3000 Series User Manual preview
Nuvo-3000 Series
Brand: Neousys Technology Pages: 101
Davey Torrium2 Installation And Operating Instructions Manual preview
Torrium2
Brand: Davey Pages: 8
RADIKAL TECHNOLOGIES SAC-2K Manual preview
SAC-2K
Brand: RADIKAL TECHNOLOGIES Pages: 36
Evoqua WALLACE & TIERNAN MULTI-FUNCTIONS-CONTROLLER Short Operating Instructions preview
WALLACE & TIERNAN MULTI-FUNCTIONS-CONTROLLER
Brand: Evoqua Pages: 4
Balboa Instruments GL8-GL8000M3-RCA-3.0 Tech Sheet preview
GL8-GL8000M3-RCA-3.0
Brand: Balboa Instruments Pages: 9
Napoleon eFIRE Operating Instructions Manual preview
eFIRE
Brand: Napoleon Pages: 8
Overland Storage NEO Agility 48 10GbE Card Instructions preview
NEO Agility 48 10GbE Card
Brand: Overland Storage Pages: 4
Naturela NPBC-V3M-1 Manual preview
NPBC-V3M-1
Brand: Naturela Pages: 28

Brands by name

Popular brands

Load more brands