manualshive.com logo in svg

Philips LPC214 Series, User Manual

The Philips LPC214 Series is a cutting-edge product designed to meet your needs. With our comprehensive and user-friendly User Manual, you can easily navigate through all the features and functionalities. Download this manual for free from our website, ensuring a hassle-free experience.

Share
Download
background image

 

© Koninklijke Philips Electronics N.V. 2005. All rights reserved.

User manual

Rev. 01 — 15 August 2005 

105

Philips Semiconductors

UM10139

Volume 1

Chapter 9: UART0

 

9.3.11  UART0 Scratch pad register (U0SCR - 0xE000 C01C)

The U0SCR has no effect on the UART0 operation. This register can be written and/or 
read at user’s discretion. There is no provision in the interrupt interface that would indicate 
to the host that a read or write of the U0SCR has occurred.

3

Framing Error

 

 (FE)

0

When the stop bit of a received character is a logic 0, a framing error occurs. 
An U0LSR read clears U0LSR[3]. The time of the framing error detection is 
dependent on U0FCR0. Upon detection of a framing error, the Rx will attempt 
to resynchronize to the data and assume that the bad stop bit is actually an 
early start bit. However, it cannot be assumed that the next received byte will 
be correct even if there is no Framing Error.

Note: A framing error is associated with the character at the top of the UART0 
RBR FIFO.

0

Framing error status is inactive.

1

Framing error status is active.

4

Break Interrupt

 

 (BI)

0

When RXD0 is held in the spacing state (all 0’s) for one full character 
transmission (start, data, parity, stop), a break interrupt occurs. Once the 
break condition has been detected, the receiver goes idle until RXD0 goes to 
marking state (all 1’s). An U0LSR read clears this status bit. The time of break 
detection is dependent on U0FCR[0].

Note: The break interrupt is associated with the character at the top of the 
UART0 RBR FIFO.

0

Break interrupt status is inactive.

1

Break interrupt status is active.

5

Transmitter 
Holding 
Register Empty

 

 (THRE))

0

THRE is set immediately upon detection of an empty UART0 THR and is 
cleared on a U0THR write.

1

U0THR contains valid data.

1

U0THR is empty.

6

Transmitter 
Empty 

 

(TEMT)

0

TEMT is set when both U0THR and U0TSR are empty; TEMT is cleared when 
either the U0TSR or the U0THR contain valid data.

1

U0THR and/or the U0TSR contains valid data.

1

U0THR and the U0TSR are empty.

7

Error in RX 
FIFO 

 

(RXFE)

0

U0LSR[7] is set when a character with a Rx error such as framing error, parity 
error or break interrupt, is loaded into the U0RBR. This bit is cleared when the 
U0LSR register is read and there are no subsequent errors in the UART0 
FIFO.

0

U0RBR contains no UART0 RX errors or U0FCR[0]=0.

1

UART0 RBR contains at least one UART0 RX error.

Table 108: UART0 Line Status Register (U0LSR - address 0xE000 C014, read only) bit description

Bit Symbol

Value Description

Reset value

Table 109: UART0 Scratch pad register (U0SCR - address 0xE000 C01C) bit description

Bit

Symbol

Description

Reset value

7:0

Pad

A readable, writable byte.

0x00

Summary of Contents for LPC214 Series





























































































































































































































































































































































Reviews:

No comments

Related manuals for LPC214 Series

S&C 6800 Series Instruction Sheet preview
6800 Series
Brand: S&C Pages: 40
Parasound 7100 Owner'S Manual preview
7100
Brand: Parasound Pages: 72
FAAC 740 D User Manual preview
740 D
Brand: FAAC Pages: 64
Wavetec Spectra Installation Manual preview
Spectra
Brand: Wavetec Pages: 17
Calsense ET1 Manual To Programming preview
ET1
Brand: Calsense Pages: 9
MaestroHome Smart Controller Quick Setup Manual preview
Smart Controller
Brand: MaestroHome Pages: 10
Hach EC1000 Instruction Manual preview
EC1000
Brand: Hach Pages: 128
Yamato V Instruction Manual preview
V
Brand: Yamato Pages: 33
H3C WX Series Configuration Manual preview
WX Series
Brand: H3C Pages: 69
Harpo BraillePen 12 Quick Start Manual preview
BraillePen 12
Brand: Harpo Pages: 35
Hardi HC 6500 Quick Manual preview
HC 6500
Brand: Hardi Pages: 2
ICP DAS USA I-7188XA User Manual preview
I-7188XA
Brand: ICP DAS USA Pages: 166
ICP DAS USA SMS-531 User Manual preview
SMS-531
Brand: ICP DAS USA Pages: 64
ICS Tunnel Master Jr Manual preview
Tunnel Master Jr
Brand: ICS Pages: 83
Saftronics CV10 Quick Start Manual preview
CV10
Brand: Saftronics Pages: 13
Newport MM4005 User Manual preview
MM4005
Brand: Newport Pages: 417
WAC T24-OD-CTR Installation Instruction preview
T24-OD-CTR
Brand: WAC Pages: 5
YOKOGAWA UP150 Instruction Manual preview
UP150
Brand: YOKOGAWA Pages: 33

Brands by name

Popular brands

Load more brands