Philips LPC214 Series User Manual Download Page 209 | Manualshive

Page: 209 / 348

background image

9397 750 XXXXX

© Koninklijke Philips Electronics N.V. 2005. All rights reserved.

User manual

Rev. 01 — 15 August 2005

209

Philips Semiconductors

UM10139

Volume 1

Chapter 14: USB Device Controller

{

/* OR with the existing value of the register */

RealizeEndpointRegister |= (UInt32) ((0x1 << endpt));

/* Load endpoint index Reg with physical endpoint no.*/

EndpointIndexRegister = (UInt32) endpointnumber;

/* load the max packet size Register */

Endpoint MaxPacketSizeReg = PacketSize;

/* check whether the EP_RLSED bit is set */

while (!(DeviceInterruptStatusReg & PFL_HW_EP_RLSED_BIT))

{

/* wait till endpoint realization is complete */

}

/* Clear the EP_RLSED bit */

Clear EP_RLSED bit in DeviceInterrupt Status Reg;

}

Device will not respond to any tokens to the un-realized endpoint. ‘Configure Device’
command can only enable all realized and enabled endpoints. For details see

14.9.2 “Configure Device (Command: 0xD8, Data: write 1 byte)” on page 223

.

14.8 EP_RAM requirements

The USB device controller uses dedicated RAM based FIFO (EP_RAM) as an endpoint
buffer. Each endpoint has a reserved space in the EP_RAM. The EP_RAM size
requirement for an endpoint depends on its Maxpacketsize and whether it is double
buffered or not. 32 words of EP_RAM are used by the device for storing the buffer
pointers. The EP_RAM is word aligned but the Maxpacketsize is defined in bytes hence
the RAM depth has to be adjusted to the next word boundary. Also, each buffer has one
word header showing the size of the packet length received.

EP_ RAM size (in words) required for the physical endpoint can be expressed as

EP_RAMsize = ((Maxpack 3) / 4 + 1)

×

db_status

where db_status = 1 for single buffered endpoint and 2 for double buffered endpoint.

Since all the realized endpoints occupy EP_RAM space, the total EP_RAM requirement is

where N is the number of realized endpoints. Total EP_RAM size should not exceed 2048
bytes (2 kB, 0.5 kwords).

EP_RAM can be accessed by 3 sources, which are SIE, DMA engine and CPU. Among
them, CPU has the highest priority followed by the SIE and DMA engine. The DMA engine
has got the lowest priority. Then again, under the above mentioned 3 request sources,
write request has got higher priority than read request. Typically, CPU does single word

TotalEPRAMsize

32

epramsize n

( )

n

0

=

N

∑

+

=

«
...
207
208
209
210
211
...
»

Summary of Contents for LPC214 Series





























































































































































































































































































































































Reviews:

No comments

Related manuals for LPC214 Series

Brand: J4C Pages: 4

Brand: 2M Technology Pages: 17

Brand: 2iB Pages: 5

Brand: V2 Pages: 12

Brand: H3C Pages: 5

Brand: z21 Pages: 2

Brand: Procom Pages: 10

Brand: Trane Technologies Pages: 8

Brand: Shimaden Pages: 32

Brand: meibes Pages: 20

Brand: Telit Wireless Solutions Pages: 49

Brand: X10 Pages: 3

Brand: Intel Pages: 334

Brand: JR Pages: 88

Brand: Eaton Pages: 3

Brand: iXBlue Pages: 20

Brand: TDSi Pages: 23

DI-DMX-WIFI-WMDC-1ZWH

Brand: DIODE LED Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands