manualshive.com logo in svg

Pfaff 3588-05/020, Instruction Manual, Page: 9 / 190

Share
Download
Pfaff 3588-05/020 Instruction Manual Download Page 9

 

 

Safety

 

9

1

.05 

Notes for operating and technical staff

1

.05.01 

Operating staff

Operating staff are the persons responsible for setting up, operating and cleaning the machi-

ne and for eliminating any malfunctioning in the sewing area.

The operating staff is obliged to observe the following points:

 

●

The notes on safety in this instruction manual must always be observed!

 

●

Any working methods, which adversely affect the safety of the machine, must be avoi-

ded.!

 

●

Loose-fi tting clothing should be avoided. No jewellery, such as chains and rings, should 

be worn!

 

●

Ensure that only authorised persons enter the danger area of the machine!

 

●

Any changes occurring on the machine, which may affect its safety, must be reported to 

the user immediately.

1

.05.02 

Technical staff

Technical staff are persons who have been trained in electrical engineering/electronics and 

mechanical engineering. They are responsible for lubricating, servicing, repairing and adjus-

ting the machine.

The technical staff is obliged to observe the following points:

 

●

The notes on safety in this instruction manual must always be observed!

 

●

Before carrying out any adjustment or repair work the main switch must be switched off 

and measures taken to prevent it from being switched on again!

 

●

Never work on parts or equipment still connected to the power supply! Exceptions are 

only permissible in accordance with the regulations EN 

50110

.

 

●

All safety covers must be replaced after the completion of maintenance or repair work! 

Summary of Contents for 3588-05/020































































































































































































Reviews:

No comments