manualshive.com logo in svg

Pfaff 3588-05/020, Instruction Manual, Page: 20 / 190

Share
Download
Pfaff 3588-05/020 Instruction Manual Download Page 20

Controls

20

Fig. 7 - 06

1

7

.06 

Control panel

The current operating conditions are displayed on control panel 

1

. Operation takes place in a 

constant dialogue between the control unit and the operator. For this purpose, depending on 

the operating condition of the machine, different symbols and/or texts are displayed. If the 

symbols or texts are framed, these show functions which can be selected by pressing the 

appropriate position on the monitor. By pressing the corresponding function this is carried 

out or switched on or off immediately, or a further menu appears, e.g. for entering a value. 

Activated functions are shown with inverted symbols. Unframed symbols or texts are only 

used for display purposes and cannot be selected by pressing.

Description of the functions

Normal symbol = function switched off (inactive)

Inverted symbol = function switched on (active)

Summary of Contents for 3588-05/020































































































































































































Reviews:

No comments