manualshive.com logo in svg

Pfaff 3588-05/020, Instruction Manual, Page: 142 / 190

Share
Download
Pfaff 3588-05/020 Instruction Manual Download Page 142

142

Adjustment

Description of the functions

Conclude input

This function is used to conclude the input and change to the sewing mode.

Speed adjustment

This function is used to increase or reduce the set speed.

Start

This function is used to start the motor running.

Stop

This function is used to stop the motor running.

Thread trimming cycle

This function is used to run the thread trimming cycle.

Needle position

The present set position of the needle is displayed.

To adjust the needle bar position to t.d.c., bring the needle bar into the appropriate position 

by turning the balance wheel, and then operate the "POS" function to take over this position. 

13

.09 

Sewing motor adjustments

 

●

Switch on the machine.

 

●

Call up the input mode.

 

●

Call up the "sewing motor adjustments".

Summary of Contents for 3588-05/020































































































































































































Reviews:

No comments