background image

28 1-800-732-2677

 

www.petsafe.net 29 

Compliance

FCC/Canada

This Class B digital apparatus complies with Canadian ICES-003. This equipment has been tested and found to comply with 

the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference when the equipment is operated in a residential environment. This equipment 

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction 

guide, may cause harmful interference to radio communications. However, there is no guarantee that interference will not 

occur in a practical installation. If this equipment causes harmful interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more 

of the following measures:
•  Relocate the interfered receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different to that to which the receiver is connected.
•  Contact the Customer Care Center at 1-800-732-2677.
This device complies with Industry Canada Rules. This device complies with part 15 of the FCC Rules. Operation is subject 

to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any 

interference received, including interference that may cause undesired operation. 
Unauthorized changes or modifications to the equipment, not approved by Radio Systems

®

 Corporation, could result in not 

meeting compliance with FCC regulations and could void the user’s authority to operate the equipment.

Australia

This device complies with the applicable EMC requirements specified by the ACMA (Australian Communications and Media 

Authority).

Customer Care International

USA & Canada - Tel: 800-732-2677 

Monday - Friday 8 AM - 8 PM / Saturday 9 AM – 5 PM
Australia - Tel: 1800 786 608 

Monday - Friday 8:30 AM - 5 PM
New Zealand - Tel: 0800 543 054 

Monday - Friday 10:30 AM - 7 PM

Summary of Contents for PIG00-100777

































Reviews: